MX-2630 (serv.man14). CCE 1835 ROM Upgrade (3) DSK V07.00.()1.00 FR51U FR52U Bulletin Only - Sharp Copying Equipment Technical Bulletin (repair manual). Page 5

Read Sharp MX-2630 (serv.man14) Technical Bulletin online

 
【Description】 
 
No. 
Item 
Description 
Model 
MX-3050N 
MX-3550N 
MX-4050N 
MX-3060N 
MX-3560N 
MX-4060N 
MX-3070N 
MX-3570N 
MX-4070N 
MX-5050N 
MX-6050N 
MX-5070N 
MX-6070N 
MX-2630N 
29 
Network 
Improvement of the procedure to restart the job which resulted 
in Limit error due to the network error 
 
 
 
 
 
30 
Network 
Correction of the following problem: 
If the e-mail with the invalid format is sent to MFP, NG85-0071 
error (data reception timeout) occurs while receiving I-Fax data, 
unable to receive subsequent jobs. 
 
 
 
 
 
31 
Network 
Correction of the problem that there are some cases where the 
polling of FSS stops and the reception of I-Fax data fails. 
 
 
 
 
 
32 
Network 
Unsupport of Mopria
 
N/A 
N/A 
N/A 
N/A 
 
33 
Copy 
Correction of the failure to make hole punch though the punch 
holes can be made when performing “Proof Copy”   
 
 
 
 
 
34 
Option 
Addition of SoftSW to switch Enable/Disable for output of non-
stapled papers in a batch: 
Sim55-01  SW3-7 
0: "Output papers in a batch" ON    (Default) 
1: "Output papers in a batch" OFF 
 
 
 
 
 
35 
Option 
Correction of the problem that Invoice-R paper cannot be ejected 
as a batch but ejected as a single page. 
 
 
 
 
 
36 
Option 
Correction of the problem that the manual Staple LED is 
illuminating even though the manual staple is prohibited while a 
job with Stapleless staple is running. 
 
 
 
 
 
37 
Option 
Correction of the problem that the message "Remove the paper" 
may not disappear if removing the paper quickly right after the 
completion of manual stapling 
 
 
 
 
 
38 
Option 
Correction of the problem that the location of the paper jam is not 
displayed if the paper jam is detected at the saddle section when 
turning ON the machine 
 
 
 
 
 
39 
Option 
Correction of the following problem: 
When the machine runs out of paper while discharging 2-sided, 
the paper smaller than A4/Letter in offset mode, the last paper 
bounce out the batch, causing alignment failure. 
 
 
 
 
 
40 
Option 
Correction of the finisher error or the paper jam caused due to 
the size illegal when switching Paper tray on the main unit 
 
 
 
 
 
41 
Image send 
Correction of the following problem:
 
MFP locks up while displaying "Sending/ Waiting" if the original 
which will be cropped cannot be detected when scanning the 
data using the cropping function(Photo/Multi) and "Send 
Destination Link" feature
 
 
 
 
 
 
 
 
○=applied 
Page of 6
Display

Click on the first or last page to see other MX-2630 (serv.man14) service manuals if exist.