Read Sharp MX-2610N / MX-3110N / MX-3610N (serv.man197) Technical Bulletin online
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-953
1. Model Name: MX-FR30U (Options for MX-2610N/3110N/3610N)
2. Description: Upgrade of ICU-ROM
From September 2011 Production
ROM control No.
ICU
D00
0300Ac
* ICU above is the version described in the ROM management label. Check that the actual
version is: ICU(MAIN): 03.00.Ac.00/ICU(BOOT): 01.00.Ac.00/LANGUAGE: 01.41.A1.00/
GRAPHIC: 01.00.A1.00/UICONTENTS: 03.00.Ac.00/PCL(MAIN): 03.00.A1.00; by Sim22-5.
version is: ICU(MAIN): 03.00.Ac.00/ICU(BOOT): 01.00.Ac.00/LANGUAGE: 01.41.A1.00/
GRAPHIC: 01.00.A1.00/UICONTENTS: 03.00.Ac.00/PCL(MAIN): 03.00.A1.00; by Sim22-5.
Item of change: See the attached sheet
Note) This report is a T/R for the data security kit option, corresponding to general
T/R No. CCE-941
Note) This report is a T/R for the data security kit option, corresponding to general
T/R No. CCE-941
ROM Version Combination History Table
No. ROM control No.
ICU
Action
(2)
C00
0200Ac
2011/7
(1)
B00
0110Ac
2011/4
ROM UPGRADE ..... (3). Ver 03.00.Ac
TECHNICAL BULLETIN
Date:
14
th
November 2011
Model:
MX2610N – MX3110N
MX3610N
Ref.:
037
Colour:
White
Page:
1 of 4
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-953
[Description]
No.
Item
Details
1 Address book
related
From the print driver, address book acquisition could not be performed. This problem
has been corrected.
has been corrected.
2 Address book
related
A check box "Apply addresses in sending mode only" has been added under [System
Settings] [FAX/Image Sending] [Operation Settings]. Only address to the contacts
of the mode, refined by job type, can now be selected. (Default: Checked)
Settings] [FAX/Image Sending] [Operation Settings]. Only address to the contacts
of the mode, refined by job type, can now be selected. (Default: Checked)
3 Address book
related
On the "Recent Addresses" display, if the dial input number is registered to the address
book after sending with direct dial input, "Recent Addresses" display would not be
updated to show the registered name of the number and it would remain as the direct
dial (number). The registered name will now update.
book after sending with direct dial input, "Recent Addresses" display would not be
updated to show the registered name of the number and it would remain as the direct
dial (number). The registered name will now update.
4 Address book
related
From the address list screen, a contact name of a contact registered to a group couldn’t
be confirmed. As an improvement, for addresses that are registered to a group, the
display of the "Address/Number" field will display as follows.
- Two line display
- 1st line displays the contact name (for direct input, the "Direct input" will be displayed).
- 2nd line will display the address or number.
be confirmed. As an improvement, for addresses that are registered to a group, the
display of the "Address/Number" field will display as follows.
- Two line display
- 1st line displays the contact name (for direct input, the "Direct input" will be displayed).
- 2nd line will display the address or number.
5
Main unit
authentication
related
authentication
related
Card authentication used with the ELWISE (Large ELWISE) card can now be supported.
When using the ELWISE card, enter a setting value “107” in [User administration]
[Card type/Card reader setting].
When using the ELWISE card, enter a setting value “107” in [User administration]
[Card type/Card reader setting].
6
Main unit
authentication
related
authentication
related
When LDAP server setting and LAN settings are not completed, the authentication
response for unregistered cards was slower. As an improvement, if the LDAP server
settings are not completed, after searching through the main unit general registered user
search with the card ID, unregistered cards will immediately return an authentication
error without the LDAP authentication.
response for unregistered cards was slower. As an improvement, if the LDAP server
settings are not completed, after searching through the main unit general registered user
search with the card ID, unregistered cards will immediately return an authentication
error without the LDAP authentication.
7
Main unit
authentication
related
authentication
related
When automatic logout is enabled on Felica (IDM) card authentication, if the card was
used for repeated fast operations, the card would not be detected. This problem has
been corrected.
used for repeated fast operations, the card would not be detected. This problem has
been corrected.
8 UI related
The check boxes "Display position in system settings" and "Enable the link for the
displayed position" have been added under [System Settings] [Operation Settings].
In the setting mode screen upper, the menu position currently displayed can be
confirmed.(Default: Checked)
displayed position" have been added under [System Settings] [Operation Settings].
In the setting mode screen upper, the menu position currently displayed can be
confirmed.(Default: Checked)
9 UI related
The settings file for the IC card user area settings can now be confirmed whether or not
the setting has been completed. In addition, to clear the settings file, a "Clear" key has
been added to [User Administration] [Card Area Settings].
the setting has been completed. In addition, to clear the settings file, a "Clear" key has
been added to [User Administration] [Card Area Settings].
10 UI related
In [System Settings] [Device Settings], one-sided/two-sided print switch settings for
list print have been added.
list print have been added.
11 UI related
On the settings screen where date and time can be specified, when the setting buttons
“+” and “-” are pressed, the date and time now operate in a loop.
“+” and “-” are pressed, the date and time now operate in a loop.
12 UI related
For the warning message display when the multi address sending is set to prohibited,
the warning message would be displayed when multi addresses are selected and the
start key is pressed. However, the display is now triggered by the 2nd address being
selected.
the warning message would be displayed when multi addresses are selected and the
start key is pressed. However, the display is now triggered by the 2nd address being
selected.
13 UI related
An "Action panel default display" check box has been added under [System Settings]
[Operation Settings]. Now, whether or not to display the action panel by default can be
selected.(Default: Checked)
[Operation Settings]. Now, whether or not to display the action panel by default can be
selected.(Default: Checked)
14 UI related
To improve the operation ability of the soft keyboard displayed for FAX number input
when registering or editing an address from the operation panel, the input area can now
be moved using the [ ] and [ ] keys.
when registering or editing an address from the operation panel, the input area can now
be moved using the [ ] and [ ] keys.
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-953
No.
Item
Details
15 UI related
The selected default display (list display/thumbnail display) on the data call screen for
document filing, can be selected separately, the base folder/temporary folder or the user
folder.(Default: list display)
[Setting location]
[System Settings] [Operation Settings] [Preview Settings]
document filing, can be selected separately, the base folder/temporary folder or the user
folder.(Default: list display)
[Setting location]
[System Settings] [Operation Settings] [Preview Settings]
16 UI related
When using pull printing from a FTP/common folder and a user name/password is
required to access the server, the authentication screen would not be displayed. Instead,
an error message (RM0001) instructing that the server could not be accessed would be
displayed. Now, an authentication dialog will be displayed.
required to access the server, the authentication screen would not be displayed. Instead,
an error message (RM0001) instructing that the server could not be accessed would be
displayed. Now, an authentication dialog will be displayed.
17 UI related
Based on the selected pattern display for the bar displayed on the screen that shows the
remaining toner, it could be difficult to see in some cases, therefore the background
design for the bar has been changed.
* Remaining toner display screen can be displayed by changing the control software SW
(Sim55-3) as follows; SW No. 22 Data 5: 0 1.
remaining toner, it could be difficult to see in some cases, therefore the background
design for the bar has been changed.
* Remaining toner display screen can be displayed by changing the control software SW
(Sim55-3) as follows; SW No. 22 Data 5: 0 1.
18 UI related
The [OK] key has been removed from the 10 key screen, and the numbers can be set
using the [X] key on the setting dialog. These corrections have been added to the
following modes.
- [System Settings] [FAX/Image Sending]
- [System Settings] [F-Code Memory Box]
using the [X] key on the setting dialog. These corrections have been added to the
following modes.
- [System Settings] [FAX/Image Sending]
- [System Settings] [F-Code Memory Box]
19 UI related
The contents of the American English messages have been fix and changed.
20 UI related
In large character mode, the right character column in the top of the action panel would
become cut off. To improve this, using a screen conversion trigger, the full screen will be
displayed for a moment and then it will return back to the original position after a
specified period of time (1 second).
become cut off. To improve this, using a screen conversion trigger, the full screen will be
displayed for a moment and then it will return back to the original position after a
specified period of time (1 second).
21 UI related
For web browsing standard machine, a web browsing icon has been displayed in the
header of the 2nd screen (home screen).
header of the 2nd screen (home screen).
22 UI related
After performing secure user login settings, if the user permissions were changed they
would not be reflected. This problem has been corrected.
would not be reflected. This problem has been corrected.
23 UI related
When the login name is set to display with "*", the displayed login name on the user list
would not be displayed with "*". This problem has been corrected.
would not be displayed with "*". This problem has been corrected.
24 UI related
When the application expansion kit is loaded and when the left or right scroll buttons
were pressed on the settings screen, incorrect fields would be displayed. This problem
has been corrected.
were pressed on the settings screen, incorrect fields would be displayed. This problem
has been corrected.
25 Copy related
When a copy job is being executed and the [Cancel printing] button was pressed, after
the "Would you like to cancel job?" message was displayed, even if the [Do not cancel]
button was pressed, in some cases the machine would stay in "Ready" and not start
printing. This problem has been corrected.
the "Would you like to cancel job?" message was displayed, even if the [Do not cancel]
button was pressed, in some cases the machine would stay in "Ready" and not start
printing. This problem has been corrected.
26 Printer related
During print output, in some cases the character would not be output correctly (The
characters would be output as " "). This problem has been corrected.
characters would be output as " "). This problem has been corrected.
27 Printer related
When printing from the AS/400, in some cases images would be slide to the left. This
problem has been corrected.
problem has been corrected.
28 Printer related
In some cases the retention hold jobs of the printer would hang-up while being analyzed.
This problem has been corrected.
This problem has been corrected.
29 Printer related
In printer retention hold job, when an odd number of pages are set for double-sided print
and print is executed, in some cases the thumbnail creation would not be correctly
completed. This problem has been corrected.
and print is executed, in some cases the thumbnail creation would not be correctly
completed. This problem has been corrected.
30 FAX related
Attached image results output jobs of a received FAX that was finished as busy would
be displayed and deleted repeatedly on a job status. This problem has been corrected.
be displayed and deleted repeatedly on a job status. This problem has been corrected.
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-953
No.
Item
Details
31 FAX related
In the over memory state (remaining memory is 3%), the machine would receive an
incoming FAX. This problem has been corrected.
incoming FAX. This problem has been corrected.
32 FAX related
When sending a FAX, the origin name would not be included in some cases. This
problem has been corrected.
problem has been corrected.
33 Image transfer
related
In the "Scan to me" function, the items [Apply when selecting the FAX/Internet FAX
screen] and [Authorize cancelation] have been added.
[Setting location]
[System Settings] [FAX/Image Sending] [Scanner Settings] [Default Address]
screen] and [Authorize cancelation] have been added.
[Setting location]
[System Settings] [FAX/Image Sending] [Scanner Settings] [Default Address]
"Use the logged in user's e-mail address"
34 Image transfer
related
From the preview screen of the received data, if the data was forwarded to the
scanner address, in some cases an NG90-0061 error would be issued. This
problem has been corrected.
scanner address, in some cases an NG90-0061 error would be issued. This
problem has been corrected.
35 Image transfer
related
In some cases, when using PC-FAX sending and a HDD write error, etc. occurred,
"Document filing function for the main unit is not available, save transmission failed"
would be displayed. This problem has been corrected.
"Document filing function for the main unit is not available, save transmission failed"
would be displayed. This problem has been corrected.
36 Document filing
related
When printing retention jobs, the message "Please wait one moment." is displayed for a
moment, and in some cases printing would not output. This problem has been corrected.
moment, and in some cases printing would not output. This problem has been corrected.
37 OSA related
A related function, "Finish copy" has been added to the copy function of OSA4.0.
[Additional Setting Items]
- Page order (sort/group/automatic) - Staple - Staple position
- Print tray - Offset
[Additional Setting Items]
- Page order (sort/group/automatic) - Staple - Staple position
- Print tray - Offset
38 OSA related
After executing an OSA scan job, in some cases the screen would be locked for 1
minute or more and screen operations would not be possible. This problem has been
corrected.
minute or more and screen operations would not be possible. This problem has been
corrected.
39 OSA related
When copying data using an OSA application, even if the balance is added to perform a
copy, the copy would not be produced. This problem has been corrected.
copy, the copy would not be produced. This problem has been corrected.
40 Web page related
In some rare cases, the SHARP logo displayed on the web page would change to
another image. This problem has been corrected.
another image. This problem has been corrected.