Read Sharp MX-2314N (serv.man68) Technical Bulletin online
Sharp Electronics (UK) Ltd., Document Systems Support
2/3
[Description]
No.
Item
Details
1
Main unit control
There were some cases where the color of the output result changed in the process of
continuous printing. This problem has been corrected.
continuous printing. This problem has been corrected.
2
Main unit control
Modification of the problem that L8-20 trouble may occur in the environment that is
printing from PC with USB connected.
printing from PC with USB connected.
3
Main unit control
Modification of an occasional failure to update the information on Tray Settings
4
Main unit control
Support for vulnerability of OpenSSL(Hear Bleed)
5
Main unit control
Modification for the problem that "No output tray is allowed." message is displayed on
Copy screen and it becomes impossible to print.
Copy screen and it becomes impossible to print.
6
Main unit control
Occasionally, toner quantity jumps to 5%. This problem has been corrected.
7
Main unit control
For the paper whose width is less than A4R in NN/NH/HH environment, the secondary
transfer current is reduced and also Soft SW which enables to set PTC to the low-output
is added.
SIM55-1:
27-6 Default: 0(OFF): 1 (ON: when printing in B/W)
27-7 Default: 0(OFF): 1 (ON: when printing in Color)
transfer current is reduced and also Soft SW which enables to set PTC to the low-output
is added.
SIM55-1:
27-6 Default: 0(OFF): 1 (ON: when printing in B/W)
27-7 Default: 0(OFF): 1 (ON: when printing in Color)
8
Main unit control
Currently the fuser pressure release operation is performed in 90 seconds after the
machine enters the ready state but the start time of fuser pressure release has been
changed to 120 minutes to enhance the life of the pressure spring.
*It is confirmed that no flat spot (unrecoverable deformation of the roller) is caused by
this countermeasure.
machine enters the ready state but the start time of fuser pressure release has been
changed to 120 minutes to enhance the life of the pressure spring.
*It is confirmed that no flat spot (unrecoverable deformation of the roller) is caused by
this countermeasure.
9
Main unit control
Fusing trouble is caused because of the adjustment to lower the fusing temperature
when the detection temperature of the machine reaches 27-degree or higher. For the
countermeasure of this issue, the fusing temperature H/H environment adjustment value
of SIM43-21 has been changed.
[Before change]: -10-degree => [After change]: 0 degree
Note) If the fusing temperature setting value of SIM43-1 is changed due to the action
from T/R No. CCE-1229, please be sure to return the value to the default (0) for both
Plain Paper/Recycled paper.
when the detection temperature of the machine reaches 27-degree or higher. For the
countermeasure of this issue, the fusing temperature H/H environment adjustment value
of SIM43-21 has been changed.
[Before change]: -10-degree => [After change]: 0 degree
Note) If the fusing temperature setting value of SIM43-1 is changed due to the action
from T/R No. CCE-1229, please be sure to return the value to the default (0) for both
Plain Paper/Recycled paper.
10 Main unit control
Enhancement of the secondary transfer output of high-voltage board to remedy the
C4-00 error which occurs under low temperature environment
C4-00 error which occurs under low temperature environment
11
Main unit Web
Description on “encryption level” has been added to "Security Settings" -> "SSL Settings"
-> "Client Port" on web page.
-> "Client Port" on web page.
12 Network
Modification of machine lockup (ex. operation panel does not function) due to the
unauthorized memory access caused by defective internal management processing in
WSD module.
unauthorized memory access caused by defective internal management processing in
WSD module.
13 Network
The modification of garbled images which appear while the data communication speed of
a device is 10 Mbps.
a device is 10 Mbps.
14 Network
Modification of a communication error which occurs in case the devices with different
MAC address share same IP address (i.e. load balancer is installed).
MAC address share same IP address (i.e. load balancer is installed).
15 Printer
Modification for the problem that the warning icon "waste-receptacle-full" is displayed
when printing with Mac OS 10.8.3 + PPD.
when printing with Mac OS 10.8.3 + PPD.
16 Printer
Some frames are missing from business forms. This problem is corrected.
17 Printer
Part of the images in an Illustrator file (by Adobe) is missing from the printout. This
problem is corrected.
problem is corrected.
18 Printer
When printing the specific PostScript PRN data with no command of paper size setting,
the data was occasionally printed with the previous paper size. This problem has been
corrected.
the data was occasionally printed with the previous paper size. This problem has been
corrected.
19 Printer
Modification of the problems that the machine may lock up / the print failure may occur
when printing the certain PS file.
when printing the certain PS file.
Click on the first or last page to see other MX-2314N (serv.man68) service manuals if exist.