MX-2310U, MX-3111U (serv.man151). MX3111U Combined Firmware V6.00G1 -Run G00-Bulletin embedded - Sharp Copying Equipment Technical Bulletin (repair manual). Page 2

Read Sharp MX-2310U / MX-3111U (serv.man151) Technical Bulletin online

 
                                                                                                                                       
CCE-1015  
 
 
 
[Description] 
No. Item 
Details 
1 Printer 
When printing a large volume of jobs with SAPL-C driver, in some cases, a part of 
the jobs could not be printed.  This problem has been corrected. 
2 Printer 
When printing with the combination of the Pamphlet function and feeding from the 
bypass tray, if the paper was emptied in the bypass tray, in some cases, the 
machine would not resume printing even though the paper was added.  This issue 
has been corrected. 
3 Printer 
When printing from the machine with the Printer Expansion Kit installed in 1W 
Energy Save mode, in some cases, the data would not be printed.  This problem 
has been corrected. 
4 Printer 
The feature to set the printable area to the same level as the previous models has 
been added to the controller SOFT SW.  
 
SIM55-3  SW No. 27  Data 7 
 0: MX-2310 series/2610 series/3610 series/4110 series/5110 series Spec (Default) 
 1: MX-2600 series/3100 series/4100 series/5001 series Spec 
5 Network 
When accessing to the file server with the sever name, in some cases, Scan to 
Network Folder would be unusable.  This problem has been corrected. 
6 Network 
When printing from the machine with the Printer Expansion Kit installed, in some 
rare cases, NIC on the machine side would be disconnected and the data would 
not be printed.  This problem has been corrected.  
7 Network 
Modification has been made not to finalize the IP address until the IP information 
is obtained from DHCP server when the setting of DHCP is enabled.   
8 Web 
Page 
When the "Sys Log" in the Service Web Page was set to "Enable", in some cases, 
the U2 error was caused by the execution of Reboot from the Web Page.  This 
problem has been corrected.   
9 Image 
Send 
When scanning to the USB memory, in some cases, it would fail with "The memory 
becomes full." message even though there was free space in the USB memory.   
This problem has been corrected. 
10 UI 
When the OSA external authentication log-in screen was displayed on Copy/Image 
Send mode, the job status on the lower left of the screen could not be displayed.  
This problem has been corrected.  
11 UI 
The feature to change the color of 2-line message from Gradation pattern to Single 
color pattern has been added to the controller SOFT SW. 
 
SIM55-3  SW No. 30  Data 1 
 0: Gradation pattern (Default) 
 1. Single color pattern 
12 UI 
If the paper types/paper sizes that could not be output as the offset was selected 
when setting up the Offset, it used to be that "The paper in the selected tray 
cannot be used for the selected mode" message would be displayed and the 
resume print was blocked as a specification.  Now it has been modified to clear the 
offset processing automatically when executing the job. (no message is displayed)
13 Trouble 
Code 
The U2 trouble that should not have been cleared unless SIM16 was executed 
could be cleared by the power-OFF/ON.  This problem has been corrected.  
 
(If the corrective firmware for this issue is installed to the machine that U2 trouble 
was cleared only by the power-OFF/ON, the U2 trouble will be displayed when the 
machine is turned ON after the completion of the installation so the appropriate 
process to clear the U2 trouble will be required.) 
14 Trouble 
Code 
For the POD1_N jam, the modification has been made not to clear the jam unless 
you open the right door.  (Jam cannot be cleared by the power-OFF/ON) 
 
 
 
 
 
Page of 2
Display

Download Sharp MX-2310U / MX-3111U (serv.man151) Technical Bulletin