Read Sharp MX-1800N (serv.man80) Technical Bulletin online
1/3
IMAGE SEND MODE,FAX MODE JOB LOG CODE LIST(CODE A-2)
CONTENTS OF CODE
CODE A-2
Content of communication interruption
33
The calling side cannot establish connection with the remote party.
34
A communication interruption command is made during sending/receiving. The interruption key
is pressed for interruption of input. <Send/Receive/Polling/Bulletin board>
is pressed for interruption of input. <Send/Receive/Polling/Bulletin board>
35
Power is failed during sending/receiving. <Send/Receive/Polling/Bulletin board>
36
Not used
37
Not used
38
Memory over during reception. <Receive/Polling>
Print is not made during reception in acting reception inhibit. <Receive/Polling>
Print is not made during reception in acting reception inhibit. <Receive/Polling>
39
Not used
40
Not used
41
The send data length of one page exceeds the limit (2m) in sending. <Send/Bulletin board>
42
The receive data length of one page exceeds the limit. <Receive/Polling>
43
Speaking before data transmission
44
A document jam occurs in direct sending. <Send>
45
Not used
46
The FAX signal from the remote party is not detected within T1 time. <Send/Polling>
(When in recall, however, the recall setting in case of a communication error is valid.)
(When in recall, however, the recall setting in case of a communication error is valid.)
47
A decode error occurs in the FAX board. <Send/Bulletin board>
Normal end of communication
OK in Internet FAX send with reception confirmation.
Normal end of communication
OK in Internet FAX send with reception confirmation.
49
The called side does not have polling function in polling reception. <Polling>
The called side has no data to send. <Polling>
The called side has no data to send. <Polling>
50
In polling reception, DCN is received for DTC. <Polling>
In polling sending, there is no send data. <Bulletin board>
In polling sending, there is no send data. <Bulletin board>
51
In poling sending, the allow number is not matched. <Bulletin board>
In polling sending, the system number is not matched. <Bulletin board>
In polling sending, the system number is not matched. <Bulletin board>
52
Not used
53
Not used
54
Not used
55
Not used
56
1) In relay command sending, DCN is received for NSS. <Send>
2) In relay command reception, a remote station number which is not registered is specified.
<Receive>
3) In F code relay broadcasting, an F code relay command is received.<Receive>
2) In relay command reception, a remote station number which is not registered is specified.
<Receive>
3) In F code relay broadcasting, an F code relay command is received.<Receive>
57
Not used
58
In reception, data are sent from a remote machine of receive inhibit number. <Receive>
(Not rejected in the bulletin board send or the F code bulletin board send.)
(Not rejected in the bulletin board send or the F code bulletin board send.)
59
In F code polling (calling), the remote machine has no DIS bit 47 (polling function). <Polling>
In F code polling (calling), the called side has no send data. (DIS bit 9 is 0.)<Polling>
In F code polling (calling), the called side has no send data. (DIS bit 9 is 0.)<Polling>
60
In F code polling (calling), DCN is received for SEP. <Polling>
In bulletin board, there is no send data for SEP. <Bulletin board>
In bulletin board, there is no send data for SEP. <Bulletin board>
61
In bulletin board, the sub address (bulletin board number (SEP)) is not matched. <Bulletin
board>
board>
62
In bulleting board, the pass code (PWD) is not matched. <Bulletin board>
63
In F code sending, the remote machine has no DIS bit 49 (sub address function). <Send>
(Check that the remote machine conforms to F code.)
(Check that the remote machine conforms to F code.)
64
In F code sending : <Send>
1) DCN is received for SUB. --- Check the box number.
2) DCN is received for SID. --- Check the box number and pass code.
In F code receiving : <Receive>"F code relay broadcasting" or "F code confidential reception"
is "Inhibited with soft SW."
1) DCN is received for SUB. --- Check the box number.
2) DCN is received for SID. --- Check the box number and pass code.
In F code receiving : <Receive>"F code relay broadcasting" or "F code confidential reception"
is "Inhibited with soft SW."
67
In F code receiving, the pass code (SID) is not matched. <Receive>
68
In F code reception, a box number which is not registered is specified. (SUB is not matched.)
<Receive>
<Receive>
69
Memory over in quick online sending <Send>
48
Click on the first or last page to see other MX-1800N (serv.man80) service manuals if exist.