AR-NC5J. AR-NC5J (Network Card) Service Manual - Sharp Copying Equipment Service Manual (repair manual)

ar-nc5j service manual
Model
AR-NC5J
Pages
12
Size
367.51 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / AR-NC5J (Network Card) Service Manual
File
ar-nc5j.pdf
Date

Read Sharp AR-NC5J Service Manual online

SERVICE MANUAL
CODE: 00ZARNC5J/A1E
DIGITAL LASER COPIER/PRINTER OPTION
PRINT SERVER CARD
AR-NC5J
AR-NC5JG
MODEL
  AR-NC5JW
CONTENTS
[1] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[2] ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[3] MAJOR FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[4] IDENTIFICATION OF EACH SECTION AND FUNCTIONS . . . . . . . . .1
[5] INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
[6] AR-NC5J STATUS CHECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
[7] TROUBLESHOOTING  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
[8] FLASH ROM VERSION UP PROCEDURE  . . . . . . . . . . . . . . . . . . . . .6
Parts marked with “
” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
AR-NC5J/NC5JG/NC5JW - 1
[1] GENERAL
The  AR-NC5J  is  a  print  server  with  Falcon  32bit  RISC  chip,  which
automatically  switches  between  10BASE-T/100BASE-TX,  conforming
to network protocols of TCP/IP (Windows95, Windows98, WindowsMe,
WindowsNT4.0, Windows2000, UNIX), IPX/SPX (Netware), AppleTalk
(Macintosh),  and  NetBEUI  (Windows95,  Windows98,  WindowsMe,
WindowsNT4.0,  Windows2000).  The  32bit  CPU,  together  with  the
automatic  switch  of  10/100BASE,  provides  high-speed  process.  This
server  allows  to  share  printers  in  a  wide  range  of  network  environ-
ments  from  a  small-sized  network  by  means  of  NetBEUI  to  a  large-
scale network where two or more network protocols are intermingled.
[2] ENVIRONMENT
1. Items required for connection to a 
network
• Shield-type, twisted-pair cable (A cable of Category 5 is required for
100BASE-TX.)
• Printer
2. Network computer
• Windows95/98/Me/NT4.0/2000
(One of TCP/IP, NetWare, or NetBEUI must be available.)
• UNIX
• NetWare
• Macintosh (AppleTalk must be available.)
[3] MAJOR FUNCTIONS
1. Functions
A. Automatic IP address setup by DHCP, BOOTP, 
RARP
(1) DHCP/BOOTP
The  AR-NC5J,  equipped  with  the  DHCP/BOOTP  protocols,  allows  to
make  setups  related  to  TCP/IP  in  a  network  where  a  DHCP/BOOTP
server is working.
By enabling the DHCP/BOOTP setup of the AR-NC5J, the information
related to TCP/IP which is valid in the DHCP/BOOTP server can be set
to the AR-NC5J.
• The  DHCP  protocol  supported  by  the  AR-NC5J  basically  conforms
to RFC2131/2132. It conforms to Windows NT DHCP servers.
• To  utilize  the  DHCP  function  of  the  AR-CN5J,  consult  the  network
manager.
(2) RARP
The AR-NC5J, equipped with the RARP protocol, allows to make setup
of IP address in a network where a RARP server is working.
By enabling the RARP setup of the AR-NC5J, the IP address set in the
RARP server can be assigned to the AR-NC5J.
B. IPP conformity (TCP/IP)
The AR-NC5J conforms  to  the  Internet printing protocol  (IPP  Ver.1.0)
which allows to print via the Internet. By using the IPP, it allows to print
with a remote printer as well as Web access by HTTP.
C. WWW browser
The AR-NC5J, equipped with the HTTP server, can be accessed by a
WWW  browser  to  display  the  printer  status  or  to  change  the  printer
setup.
• For  operations  of  HTTP,  it  is  recommendable  to  use  a  WWW
browser  such  as  Internet  Explore4.0  or  later  or  Netscape
Navigator4.0 or later. If another browser is used, it must at least con-
form to HTTP1.0 (RFC1945) or HTML2.0 (RFC1866).
• To  use  HTTP,  the  TCP/IP  protocol  setup  of  the  AR-NC5J  must  be
valid and the IP address of the AR-NC5J must be set.
2. Hardware specifications
[4] IDENTIFICATION OF EACH 
SECTION AND FUNCTIONS
1. Connector and LEDs
<Status LED flashing cycle>
CPU
FALCON 32bit RISC chip
Memory
RAM
4Mbyte
Flash ROM
1MByte
Network interface 10BASE-T/100BASE-TX
1 port (10/100BASE 
auto recognition)
Printer interface
Sharp's unique interface
Other
LED lamp
Status
10Base LINK,
100Base LINK
(3 pcs.) 
1
Connector for 
10BASE-T/
100BASE-TX
Connected with a shield-type, twisted-pair 
cable. (For 100BASE-TX environment, use 
a cable of Category 5.)
2
10BASE LINK LED 
(Green)
When a network connection is established 
in 10BASE-T, this lamp lights up.
100BASE LINK 
LED (Green)
When a network connection is established 
in 100BASE-TX, this lamp lights up.
3
STATUS LED 
(Orange)
During communication, this lamp flashes.
Content of operation
Lighting pattern
Cycle
Error detection
0.2sec/rapid flashing
Forcible loader mode
1sec/slow flashing
Refer to [8]-4-(a).
Factory setup mode
Repetition of 0.6sec/
2times flashing
ON
OFF
10/100BASE
1
2
3
LINK
10B
100B
STAT
0.2 sec
1 sec
0.6 sec
AR-NC5J/NC5JG/NC5JW - 2
2. Jumper switches
The jumper switch has No. 1 and No. 2 pins, and ON/OFF is switched
by the jumper plug.
When getting started, No. 1 pin is ON and the flash memory loader is
started.  When  No.  2  is  ON,  the  factory  setting  of  the  environmental
variable is performed.
NOTE:
• When setting the jumper switch, be sure to turn off the power of the
printer.
• For  normal  use,  be  sure  to  set  No.  1  and  No.  2  to  OFF  (Normal
mode).
• The  factory  setup  can  be  set  by  the  utility  or  Telnet  as  well  as  the
above jumper switch setup operations. Normally the utility or Telnet
is used. Setting by the jumper switch is used only when the unit can-
not make communication with the AR-NC5J.
[5] INSTALLATION
1. Connection to a network
To connect the AR-NC5J to a network, the following items are required.
• For connection in the 100BASE-TX environment, a hub conforming
to  100BASE-TX  and  a  shield-type,  twisted-pair  cable  (Category  5)
are required. 
1) Check  that  the  printer  power  is  off,  and  connect  the  shield-type,
twisted-pair cable to the 10/100BASE connector of the AR-NC5J.
2) Connect the other end of the cable to the hub.
3) Turn on the printer power, and check that the printer operates nor-
mally.
2. Parts included
3. Installation procedure
The  AR-NC5J  installing  procedures  in  the  AR-235/275  series  are
described.
In this case, no spacer is used in the packed items of the AR-NC5J.
For the installing procedures of the AR-NC5J to another printer, refer to
the printer's Service Manual or Installation Manual.
Turn off the main switch of the copier and then remove the power 
plug of the copier from the outlet.
1) Remove the shielding plate.
Remove five screws and remove the shielding plate.
2) Cut and remove the cut-out portion from the left rear cabinet.
Cut and remove the cut-out portion from the left rear cabinet using
a tool such as nippers. (Be careful about the direction of the tool so
that the cut surface is flat.)
Jumper witch
ON
OFF
1
Forcible loader mode Normal mode (When shipping)
2
Factory setup mode
Normal mode (When shipping)
Normal mode
(When shipping)
Forcible loader mode
Factory setup
Hub
Shield-type, twisted-pair cable
1 2 3 4
10BASE-T/
100BASE-TX
connector
Jumper switch
1
2
Jumper plug
1
2
1
2
1 2
3 4
5
6 7
8
Print server card: 1
Screws (silver)
M3 x 8: 2
Spacers (unused): 2
CD-ROM: 1
Operation manual: 1 Installation manual: 1
Screws
Cut-out portion
AR-NC5J/NC5JG/NC5JW - 3
3) Attach the print server card.
Align  the  connector  positions,  connect  the  print  server  card,  and
then secure the card to the option mounting plate in the main unit
using supplied two silver screws (M3 x 8).
4) Reattach the shielding plate.
Reattach the shielding plate using five screws.
5) Connect the cable to the control PWB.
Connect a LAN cable to the connector of the print server card.
Insert the power plug of the copier to the outlet and turn on the 
main switch. Then, carry out the following procedure.
6) Check for the print server card.
Use the keys on the operation panel to print a configuration page.
Check that the network interface card has been installed.
7) Check for printing.
Peform setup of the environmental variables. (refer to [6]-2)
(For installation of printer drivers on a computer and network set-
tings (IP address input), see the supplied operation manual.)
Execute printing to check to see if printing can be executed prop-
erly.
[6] AR-NC5J STATUS CHECK
1. Printing the status page
The AR-NC5J status is checked by printing the status page.
A. Example of status page print
There are roughly two ways of printing the status page.
• Printing the status page is performed when starting the AR-NC5J.
Refer to the manual on the AR-NC5J setup.
• Perform printing  of the status page  from the operation panel of the
printer.
→ 
Some printers may not support it. Refer to the Operation Manual
of the printer.
The same information as the status page print-out can be obtained
from the utility Web page.
<Example of the status page>
Silver screws
 (M3 x 8)
Print server card
Screws
LAN cable
Page of 12
Display

Download Sharp AR-NC5J Service Manual (Repair Manual)

Here you can read online and download Sharp AR-NC5J Service Manual in PDF. AR-NC5J service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AR-NC5J Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.