AR-M620 (serv.man169). 023-Prevention of POD1_N misfeeds due to the paper caught on the drum separator pawl section. - Sharp Copying Equipment Technical Bulletin (repair manual)

ar-m620 (serv.man169) technical bulletin
Model
AR-M620 (serv.man169)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
225.7 KB
Type
PDF
Document
Technical Bulletin
Brand
Device
Copying Equipment / 023-Prevention of POD1_N misfeeds due to the paper caught on the drum separator pawl section.
File
ar-m620-sm169.pdf
Date

Read Sharp AR-M620 (serv.man169) Technical Bulletin online

Sharp Electronics (UK) Ltd., Technical Services Group
ARE666
1. Model Name
ARM550/620U
2.Symptom
The separator pawls may stick allowing the paper to get caught on them causing
POD1_N misfeeds.
3. Description
The shape of the separator pawl shaft cap, separator pawl shaft pick and the separator
pawl solenoid fixing plate has been changed to prevent the pawls from sticking.
4. Action
Running changes from March 2004 production.
5. Parts Action
Prevention of POD1_N misfeeds due to the paper
caught on the drum separator pawl section.
TECHNICAL BULLETIN
Date:
02 November 2004
Model: 
ARM550/620U
Ref.:
023
Colour: 
White
Page:
1 of 4
Sharp Electronics (UK) Ltd., Technical Services Group
ARE666
Improvement procedure for the process unit.
1.  Remove the screw that fixes the process transport pass cover, and remove the
process transport pass cover by sliding it to the rear side.
2.  Remove the connector of the separator pawl solenoid, and remove the 2 screws that
fix the process harness guide (rear side).
3.  Remove the screw that fixes the separator pawl arm, then remove the separator pawl
arm and solenoid. Replace the separator pawl solenoid fixing plate.
4.  Remove the separator pawl solenoid return spring.
Sharp Electronics (UK) Ltd., Technical Services Group
ARE666
5.  Remove the separator pawl shaft.
5-1.  Pull out the separator pawl shaft from the process unit by sliding it to the rear of the
unit, at the same time pull out the separator pawl shaft earth spring.
5-2.  Pull out the separator pawl shaft from the process unit by sliding it to the front of
the unit.
6.  Remove the four E type rings and pins on the separator pawl shaft and replace the
separator pawl shaft cap.
6-1.  Remove the E type rings, separator pawl shaft cap and the SP pins.
Sharp Electronics (UK) Ltd., Technical Services Group
ARE666
7.  After inserting the SP pin till it protrudes to one side insert the separator pawl shaft
pick and refit the E type ring, this process is repeated four times.
8.  Insert the separator pawl shaft in the reverse procedure as when removing, (note the
separator pawl shaft is to be set with it’s face up).
9.  Remove the screw of the separator pawl waver bearing B, and slide the separator
pawl waver bearing B to the front side.
10.  When the separator pawl waver bearing B has slid to the front side faace the
separator pawl shaft pick facing down. Be sure to insert the boss portion of the
separator pawl pick to the inside of the separator pawl holder.
11.  Restore the separator pawl waver bearing B as before and fix it by the screw.
12.  Assemble by following the procedure from Number 1 to Number 4 in reverse order.
Page of 4
Display

Download Sharp AR-M620 (serv.man169) Technical Bulletin

Here you can read online and download Sharp AR-M620 (serv.man169) Technical Bulletin in PDF. AR-M620 (serv.man169) technical bulletin will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AR-M620 (serv.man169) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.