AR-M165-207 (serv.man25). AR-FX11 (Fax Option for AR-M165 and AR-M207) Operation Manual. - Sharp Copying Equipment User Guide / Operation Manual. Page 99

Read Sharp AR-M165-207 (serv.man25) User Guide / Operation Manual online

97
KEY OPERATOR PROGRAMS
8
5
Enter your fax number with the numeric 
keys and then press the [OK] key.
• If you make a mistake, press the [C] key and re-enter 
the number.
• To enter "+", press the 
 key.
6
Enter your name and then press the 
[START] key (
).
See "ENTERING CHARACTERS" (page 82) for the 
procedure for entering letters.
SPEAKER VOLUME
This setting is used to adjust the on-hook volume, the 
ringing volume, the line monitor volume, the TX/RX 
end sound volume, the original scanning end sound 
volume, and the tone output volume. All volume 
settings are initially set to "MIDDLE".
1

Follow steps 1 through 6 of "INITIAL 
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or 
[
] key and then press the [OK] key.
3
Select "SPEAKER VOLUME" with the [
] 
or [
] key and then press the [OK] key.
4
Select name of the volume that you wish 
to adjust with the [
] or [
] key and then 
press the [OK] key.
5
Select the desired volume level with the 
[
] or [
] key and then press the [OK] key.
• "HIGH", "MIDDLE" or "LOW" can be selected for the 
on hook volume.
• "HIGH", "MIDDLE", "LOW" or "OFF" can be selected 
for volumes other than the on hook volume.
TX/RX END SOUND
This program is used to select the beep pattern that 
signals the end of transmission or reception. "PATTERN 
1", "PATTERN 2" or "PATTERN 3" can be selected.
1

Follow steps 1 through 6 of "INITIAL 
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or 
[
] key and then press the [OK] key.
3
Select "TX/RX END SOUND" with the [
] 
or [
] key and then press the [OK] key.
4
Select "SEND" or "RECEIVE" with the [
] 
or [
] key and then press the [OK] key.
5
Select "PATTERN 1", "PATTERN 2", or 
"PATTERN 3" with the [
] or [
] key and 
then press the [OK] key.
Before pressing the [OK] key to store your selection, 
you can press the 
 key to listen to the selected 
pattern.
TX/RX END SOUND LENGTH
This setting is used to select the length of the end sound 
in seconds. Selections are "2.0 sec", "2.5 sec", "3.0 sec", 
"3.5 sec", and "4.0 sec". "3.0 sec" is normally selected.
1

Follow steps 1 through 6 of "INITIAL 
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or 
[
] key and then press the [OK] key.
3
Select "TX/RX END SOUND LENGTH" with 
the [
] or [
] key and then press the [OK] 
key.
4
Select the number of seconds with the [
] 
or [
] key and then press the [OK] key.
EXTENSION TEL
Enable this setting when an extension telephone is 
connected to the machine. An extension telephone 
connected to the machine cannot be used until this 
setting is enabled. The initial setting is enabled.
1

Follow steps 1 through 6 of "INITIAL 
PROCEDURE" (page 94).
2
Select "INITIAL SETTING" with the [
] or 
[
] key and then press the [OK] key.
3
Select "EXTENSION TEL" with the [
] or 
[
] key and then press the [OK] key.
• The setting is enabled and a checkmark 
appears in the checkbox.
• If this procedure is performed when the setting 
is enabled, the checkmark will be cleared and 
the setting disabled.
To clear the programmed fax number and 
name, follow these steps:
(1) Select "DELETE" in step 4 and then 
press the [OK] key.
(2) Select "DELETE" with the [
] or [
] 
key and then press the [OK] key.
Note
Pegasus-E_Fax_Ex.book  97 ページ  ２００４年１０月１８日　月曜日　午後８時４１分
Display
Click on the first or last page to see other AR-M165-207 (serv.man25) service manuals if exist.
Random: