Read Sharp AR-LC6 (serv.man2) Service Manual online
AR-LC6 ADJUSTMENT 6 - 2
1) Set the resist amount adjustment mode of SIM 51-02 by the key
operation of the machine.
2) In SIM 51-02, the display is shown as follows. The resist amount
adjustment value can be set for each paper feed tray.
3) Select "0: TRAY SELECT" and press START key.
The display is shown as follows. Select "6: LCC" as the paper feed
tray, and press START key.
tray, and press START key.
4) The display is shown as follows again. Select "7: LCC" and press
START key.
5) Then enter the adjustment value with 10-key.
(Default: 50, Adjustment range: 0 – 99)
• When the adjustment value is increased by 1, the resist amount
is increased by 1msec.
6) Enter the adjustment value and press START key, and printing is
started and the set value is stored.
7) After completion of the adjustment, press [CA] key to terminate the
simulation mode.
1) Set the print lead edge adjustment mode of SIM 50-5 by the key
operation of the machine.
2) In SIM 50-5, the display is shown as follows. The resist amount
adjustment value can be set for each paper feed tray.
3) Select "0: TRAY SELECT" and press START key.
The display is as shown below. Select "6: LCC" as the paper feed
tray and press START key.
tray and press START key.
4) The display is as shown below again. Select "8: LCC" and press
START key.
5) Then, enter the adjustment value with 10-key.
(Default: 50, Adjustment range: 0 – 99)
• When the adjustment value is increased by 1, the resist amount
is increased by 1msec.
6) After entering the adjustment value, press START key, and print-
ing is started and the set value is stored.
7) After completion of the adjustment, press [CA] key to terminate the
simulation mode.
ADJ 2
Resist amount adjustment
ADJ 2A
Adjustment in the resist amount
adjustment mode
adjustment mode
#/P
C
∗
5
1
2
∗
1
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. SELECT 0-14, AND PRESS START.
0.TRAY SELECT
1
1.PRINT START
2.TRAY1
50
3.TRAY2
50
4.TRAY3
50
5.TRAY4
50
6.BPT
50
7.LCC
50
8.ADU
50
9.SPF(TOP)
50
10.SPF(HIGH)
50
11.SPF(LOW)
50
12.SPF FEED(TOP)
50
13.SPF FEED(HIGH)
50
14.SPF FEED(LOW)
50
1
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. SELECT 1-6, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
1
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. SELECT 0-14, AND PRESS START.
0.TRAY SELECT
1
1.PRINT START
2.TRAY1
50
3.TRAY2
50
4.TRAY3
50
5.TRAY4
50
6.BPT
50
7.LCC
50
8.ADU
50
9.SPF(TOP)
50
10.SPF(HIGH)
50
11.SPF(LOW)
50
12.SPF FEED(TOP)
50
13.SPF FEED(HIGH)
50
14.SPF FEED(LOW)
50
50
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
7.LCC
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. NOW PRINTING.
ADJ 2A
Adjustment in the print lead edge
adjustment mode
adjustment mode
#/P
C
∗
5
0
5
∗
2
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 0-12, AND PRESS START.
0.TRAY SELECT
LEAD EDGE ADJUSTMENT. SELECT 0-12, AND PRESS START.
0.TRAY SELECT
1
1.PRINT START
(ADJUSTMENT DATA)2.RRCB
50
3.TRAY1
50
4.TRAY2
50
5.TRAY3
50
6.TRAY4
50
7.BPT
50
8.LCC
50
9.ADU
50
(VOID AREA SETTING) 10.DENA
50
11.DENB
30
12.FR VOID
30
1
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 1-6, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
2
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 0-12, AND PRESS START.
0.TRAY SELECT
LEAD EDGE ADJUSTMENT. SELECT 0-12, AND PRESS START.
0.TRAY SELECT
1
1.PRINT START
(ADJUSTMENT DATA)2.RRCB
50
3.TRAY1
50
4.TRAY2
50
5.TRAY3
50
6.TRAY4
50
7.BPT
50
8.LCC
50
9.ADU
50
(VOID AREA SETTING) 10.DENA
50
11.DENB
30
12.FR VOID
30
50
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
8.LCC
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. NOW PRINTING.
Click on the first or last page to see other AR-LC6 (serv.man2) service manuals if exist.