Read Sharp AR-FN1 (serv.man3) Service Manual online
SERVICE MANUAL
3-TRAY FINISHER
MODEL
AR-FN1
SHARP CORPORATION
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
[ 1 ] BASIC SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[ 2 ] UNPACKING AND INSTALLATION. . . . . . . . . . . . . . . . . . . . . . 2-1
[ 3 ] PICTORIAL NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[ 4 ] OUTLINE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[ 5 ] DISASSEMBLY AND REINSTALLATION . . . . . . . . . . . . . . . . . 5-1
[ 6 ] ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[ 7 ] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[ 8 ] TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[ 9 ] DESCRIPTION OF CIRCUITS. . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[10] CIRCUT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
CONTENTS
(Danish)
ADVARSEL !
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to manufacturer’s instructions.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French)
ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
CAUTION FOR BATTERY REPLACEMENT
[2] UNPACKING AND INSTALLATION
1. Unpacking
Refer to the sketch below for unpacking.
2 – 1
2. Installation
1. Attach the lock plate and mounting plate.
Remove the two screws from the upper left cabinet of the copier and
attach the lock plate to the upper left cabinet using two screws D.
attach the lock plate to the upper left cabinet using two screws D.
2. Attach the mounting plate.
Cut out the two mounting holes (the leftmost hole and the third hole
from the left) at the lower part of the desk using a Phillips screwdriver,
etc., and remove the burrs using a flat-blade screwdriver, etc.
Then, attach the mounting plate to the lower part of the desk using
two screws A.
from the left) at the lower part of the desk using a Phillips screwdriver,
etc., and remove the burrs using a flat-blade screwdriver, etc.
Then, attach the mounting plate to the lower part of the desk using
two screws A.
3. Attach the connecting plate to the finisher.
Insert the connecting plate into the lower part of the finisher and
attach the plate at the position with mark B using screw B.
attach the plate at the position with mark B using screw B.
4. Insert the connecting plate of the finisher into
the mounting plate of the desk.
Insert the connecting plate which has been attached to the finisher
into the mounting plate of the desk.
Move the finisher away from the copier after insertion to check that
the connecting plate is locked.
While the plate is locked, attach the securing plate using two black
screws C.
into the mounting plate of the desk.
Move the finisher away from the copier after insertion to check that
the connecting plate is locked.
While the plate is locked, attach the securing plate using two black
screws C.
Lock plate: 1
Mounting plate: 1
Staple cartridge: 1
Connecting plate: 1
Stapling position
label A: 1
label A: 1
Stapling position
label B: 1
label B: 1
Tray 3: 1
Exit trays: 2
Securing plate: 1
Screws A: 2
Screw B: 1
Screws C: 2
Screws D: 4
Screws for upper
left cabinet
left cabinet
Lock plate
Screws D
Screws A
Mounting plate
Mounting hole
Screw B
Connecting plate
Mounting plate
Connecting plate
Securing plate
Screws C
2 – 2
