Read Sharp AR-F13 (serv.man2) Service Manual online
AR-F13 ADJUSTMENTS 8-2
C. Registering the Number of Punch Hole
Perform the following to store (register) the type of punch unit (number of
holes) in the IC on the punch controller PCB for identification by the
finisher. Be sure to register the type whenever you have replaced the
punch controller PCB.
punch controller PCB.
1) Set bits 1 through 4 on the DIPSW1001 on the punch controller PCB
as follows:
2) Press SW1002 on the punch controller PCB to select the appropriate
number of punch holes.
•Each press on SW1002 moves the selection through the following
(repeatedly from top to bottom).
3) Press SW1003 on the punch controller PCB twice. The presses will
store the selected number of punch holes on the punch controller
PCB.
•A single press on SW1003 will cause the LED indication to flash;
another press on SW1003 will cause the indication to remain ON to
indicate the end of registration.
4) Shift all bits of DIPSW1001 to OFF.
D. After Replacing the EEP-ROM (IC1001)
1) Turn off the host machine.
2) Set bits 1 through 4 on the DIPSW1001 on the punch controller PCB
as follows:
3) Press SW1002 and SW1003 on the punch controller PCB at the
same time.
•The presses will initialize the EEP-ROM. At the end, all LEDs
(LED1001, LED1002, LED1003) will go ON.
4) Adjust the sensor output, and store the number of punch holes.
E. Setup by the diag simulation of the printer
(1) When installed to the printer model
(AR-C260M, DM-C260P)
1) Select "CONSOLE FIN. SET X" in the diag mode.
2) Select the setup value to be changed with [
] [
] keys.
The adjustable setup values are shown in the table below.
(2)When installed to the multi-function model
1) Select "CONSOLE FINISHER SETTING" in SIM 3-10.
2) Select a setup item and change the setup value.
The adjustable setup values are shown in the table below.
Number of punch holes
LED1001
LED1002
LED1003
2 holes (Puncher Unit-J1)
ON
OFF
OFF
2/3 holes (Puncher Unit-K1)
ON
ON
OFF
4 holes (Puncher Unit-G1)
OFF
OFF
OFF
4 holes (Puncher Unit-H1)
OFF
OFF
ON
ON
1
2
3
4
ON
1
2
3
4
CONSOL FIN. SET X
X:
Adjustment content
Default
value
Setup
range
range
Change/Setup
value 1
A Saddle binding position
adjustment
0 - 400
0.0707mm
B Saddle folding position
adjustment
0 - 400
0.0525mm
C Front alignment position
adjustment
0 - 20
0.367mm
D Rear alignment position
adjustment
0 - 20
0.367mm
E Staple front one-position
binding position adjustment
0 - 200
0.04374mm
F Staple rear one-position
binding position adjustment
0 - 200
0.04374mm
G Staple 2-position binding
center adjustment
0 - 200
0.04374mm
H Staple 2-position binding pitch
0 - 99
0.04374mm
I
Punch center position
adjustment (FR direction)
adjustment (FR direction)
0 - 99
J Punch hole position
adjustment
0 - 99
0.105mm
Adjustment content
Default
value
Setup
range
range
Change/Setup
value 1
1 Saddle binding position
adjustment
200
0 - 400
0.0707mm
2 Saddle folding position
adjustment
200
0 - 400
0.0525mm
3 Front alignment position
adjustment
10
0 - 20
0.367mm
4 Rear alignment position
adjustment
10
0 - 20
0.367mm
5 Staple front one-position
binding position adjustment
100
0 - 200
0.04374mm
6 Staple rear one-position
binding position adjustment
100
0 - 200
0.04374mm
7 Staple 2-position binding
center adjustment
100
0 - 200
0.04374mm
8 Staple 2-position binding pitch
adjustment
50
0 - 99
0.04374mm
9 Punch center position
adjustment (FR direction)
50
0 - 99
10 Punch hole position
adjustment
(paper feed direction)
(paper feed direction)
50
0 - 99
0.105mm
SIMULATION 3-10
CONSOLE FINISHER SETTING. SELECT 1-10, AND PRESS START.
1. SADDLE POSITION 2. FOLDING POSITION
3. FRONT ADJUST
4. REAR ADJUST 5. STAPLE REAR
6. STAPLE FRONT 7. STAPLE BOTH
8. STAPLE PITCH 9. PUNCH CENTER
10. PUNCH HOLE
1. SADDLE POSITION 2. FOLDING POSITION
3. FRONT ADJUST
4. REAR ADJUST 5. STAPLE REAR
6. STAPLE FRONT 7. STAPLE BOTH
8. STAPLE PITCH 9. PUNCH CENTER
10. PUNCH HOLE
1
SIMULATION 3-10
CONSOLE FINSHER SETTING
1.FOLDING POSITION
720
Pressing START key
starts the operation.
Pressing CUSTOM SETTING key
stops the operation.
Stops at the end of the operation.
Click on the first or last page to see other AR-F13 (serv.man2) service manuals if exist.