AR-D16. Service manual - Sharp Copying Equipment Service Manual (repair manual)

ar-d16 service manual
Model
AR-D16
Pages
36
Size
1.59 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Service manual
File
ar-d16.pdf
Date

Read Sharp AR-D16 Service Manual online

CONTENTS
Parts marked with “
” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
SERVICE MANUAL
CODE : 00ZARSP5//A1E
DIGITAL COPIER OPTIONS
AR-SP5
 (SPF)
AR-D16
 (1 TRAY UNIT)
AR-PG2
 (GDI/Scanner Kit)
MODEL
AL-12PKM
 (GDI/Scanner Kit)
AR-D16
AR-SP5
AR-PG2
AL-12PKM
[ 1 ]  GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[ 2 ]  UNPACKING AND INSTALLATION  . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
[ 3 ]  AR-SP5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
[ 4 ]  AR-D16  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
[ 5 ]  AR-PG2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
PARTS GUIGE
AR-SP5  GENERAL  1 - 1
[1] GENERAL
1. List of available options
: Option available
: Option not available
2. Outline and specifications of each option
A. AR-SP5 (Single Pass Feeder)
The single pass feeder (SPF) holds up to 30 originals for automatic
feeding.
Part names
Specifications
B. AR-D16 (250 - Sheet Paper Feed Unit)
The paper feed unit provides the convenience of increased paper
capacity for the copier and a greater choice of paper sizes readily
available for copying.
Part names
Specifications
C. AR-PG2, AL-12PKM (GDI/Scanner Expansion Kit)
*1: Feed paper lengthwise only.
*2: Data transmission time is not included.
Model
AR-122E
AR-152E
AR-153E
AR-157E
Option
AR-SP5
(SPF)
AR-D16
(1 TRAY UNIT)
AR-PG2
(GDI/Scanner Kit)
AL-12PKM
(GDI/Scanner Kit)
Acceptable 
originals
Weight: 14 to 23.9 lbs.
Size: 5-1/2" 
×
 8-1/2" to 8-1/2" 
×
 14"
Capacity: Up to 30 sheets
Power supply
Drawn from the copier
Weight
Approx. 6.6 lbs. (3kg)
Dimensions
19.6" (W) 
×
 15" (D) 
×
 4.3" (H)
(498 mm (W) 
×
 380 mm (D) 
×
 110 mm (H))
Document feeder tray
Feeding roller cover
Original guides
SPF exit area
Copy paper size
5-1/2" 
×
 8-1/2" to 8-1/2" 
×
 14"
Paper weight
15 lbs. to 21 lbs.
Paper capacity
One paper tray with capacity for 250 sheets of 
21 lb. bond paper
Weight
Approx. 6.6 lbs. (3 kg)
Dimensions
19.6" (W) 
×
 15.6" (D) 
×
 3.5" (H)
(498 mm (W) 
×
 395 mm (D) 
×
 88 mm (H))
Power supply
Drawn from the copier
Printing system
Dry, electrostatic transfer
Printing size
A6 to A4 (3-1/2" 
×
 5-1/2" to 8-1/2" 
×
 14") *1
Print speed
Max. 12 pages/min. (Letter or A4)
Continuous printing
Max. 99 pages subtractive counter
First-print time 
(Approximately)
9.6 seconds (Paper: A4) *2
Resolution
Printer
600 dpi
Scanner
600 
×
 1200 dpi
Emulation
SHARP GDI
Page orientation
Portrait or landscape
Interface port
USB interface (USB1.1 Standard)/
IEEE1284-compliant bi-directional parallel 
interface (Only for printer)
Side cover
Tray
AR-SP5  UNPACKING AND INSTALLATION  2 - 1
[2] UNPACKING AND INSTALLATION
1. AR-SP5 Installation Manual
Turn the main switch to the “OFF” position and remove the power plug
from the outlet.
1) Remove the document cover.
Remove the document cover from the copier.
2) Remove the rear cabinet.
Remove the four screws and then remove the rear cabinet.
3) Remove the hinge guides L and R.
Remove the screws (two for each) and then remove the hinge
guides L and R.
4) Remove the rear cover for the document glass.
<1> Remove the screw and then remove the right glass holder.
<2> Slide the rear cover for the document glass to remove it.
5) Attach the book sensor unit.
Insert the actuator of the book sensor unit into the mounting por-
tion in the copier and fix it using the supplied screw (M3 
×
 8).
Note: When attaching the sensor unit, fix it using the screw while
pushing the unit upward.
Connect the connector to the connector of the copier and arrange
the wiring as shown in the illustration.
 Hinge guide L
 Hinge guide R
 Installation manual, 1 sheets
 Parts included
 Screws (M3 
×
 8), 1 pcs.
 SPF unit
 
SPF rear cover, 1 pc.
 
Book sensor unit, 1 pc.
1
2
Actuator
1
3
2
AR-SP5  UNPACKING AND INSTALLATION  2 - 2
6) Attach the SPF rear cover.
<1> Pass the actuator of the book sensor into the hole of the SPF
rear cover and slide the SPF rear cover to attach it. At this
time, check that the pawl on the back side of the SPF rear
cover is inserted into the copier frame.
<2> Reattach the right glass holder to its original position and fix it
using the screw.
Note: Check that the actuator moves smoothly.
Take care to prevent entry of dirt into the scanner unit.
7) Attach the hinge guides L and R.
Attach the hinge guides L and R by fitting the pawls (two for each)
into the frame of the copier and secure them with the two screws
for each that have been removed in step 3.
8) Place the SPF on the copier.
9) Connect the SPF with the copier using the relay harness.
<1> Fit the snap band to the position shown in the illustration.
<2> Connect the connector.
<3> Fit the grounding terminal using the supplied screw (M3 
×
 8).
10) Attach the rear cabinet.
Remove the rib from the rear cabinet.
Note: While pushing down the actuator of the sensor unit, attach
the rear cabinet so that the actuator is inserted into the hole
of the rear cabinet.
<1> Hang the four pawls shown in the illustration below on the
plate.
<2> Push down the actuator of the sensor unit.
<3> Position the cabinet to the upper screw positions.
<4> Ensure that the actuator is inserted into the square hole of
the cabinet.
1
2
Pawls
Pawls
1
2
3
Pawl
Side view
Pawl
M3
×
8
M4
×
12
M3
×
8
Page of 36
Display

Download Sharp AR-D16 Service Manual (Repair Manual)

Here you can read online and download Sharp AR-D16 Service Manual in PDF. AR-D16 service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AR-D16 Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.