Read Sharp AR-C330 (serv.man4) Service Manual online
CONTENTS
Parts marked with “
” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
SERVICE MANUAL
CODE: 00ZARPX5//A1E
PRINTER I/F KIT
AR-PE3
MODEL
AR-PX5
[1] OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[2] SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
PARTS GUIDE
AR-PE3/PX5 - 1 -
[1] OUTLINE
This unit is used to connect the printer controller with the scanner
and the printer section in the AR-C330.
and the printer section in the AR-C330.
1. Unit composition
This unit is composed of the following major parts:
AR-PE3
• Controller
• I/F card
• Connection cable: 2 pcs.
AR-PX5
• Power supply unit
2. Outline of operations
(Printer mode)
Each color image data of 8bit of Y/M/C/K outputted from the print
controller.
controller.
(Scanner mode)
Each color image data of 8bit of R/G/B scanned by the scanner is
inputted to the printer I/F card.
inputted to the printer I/F card.
(Circuit system)
High-speed data transmission/reception is performed between the
engine and the print controller.
engine and the print controller.
[2] SETUP
Necessary tools: Screwdriver
1. Unpacking
(Parts list)
AR-PE3
AR-PX5
2. Parts assembly
1) Remove the operation unit.
Left side
Right side
2) Remove the left and right upper cabinet.
3) Remove the ICU PWB shield plate.
4) Remove the CCD flat cable connector.
No.
Part name
Quantity
1
Controller
1
2
40p I/F cable
1
3
20p I/F cable
1
4
I/F card
1
5
Wake Up harness
1
No.
Part name
Quantity
1
Power supply unit
1
2
M4 screw
16
3
Harness clamp
1
4
Snap band
3
5
I/F cover
1
6
Wire saddle
1
7
Caution label for connection units (Europe only)
1
AR-PE3/PX5 - 2 -
5) Open the scanner (reading) unit and fix it with the hold shaft.
6) Remove the interface cabinet.
7) Remove the cover plate on rear cabinet.
Removed screw is used for attach the printer I/F card.
8) Attach the printer I/F card with the cover plate fixing screws.
Connect the Wake Up signal harness and fix it with the snap
band.
band.
9) Attach the I/F cover with seven screws (M4 x 6). Pass the
Wake Up signal harness through the wire clamp.
10) Connect two I/F cables. Remove the screw of the ICU cover,
and fix the harness clamp and the I/F cable with the removed
screw.
screw.
11) Fix two screws (M4 x 8) temporarily, and install the printer
power unit temporarily. Fix the above two screws securely and
fix one additional screw (M4 x 8). Connect the connector and
fix with the snap band.
fix one additional screw (M4 x 8). Connect the connector and
fix with the snap band.
AR-PE3/PX5 - 3 -
12) Remove the screws, and slide and remove the printer control-
ler cover.
13) Fix the three screws (M4 x 10) temporarily.
14) Engage the notch section in the lower side of the printer con-
troller with the temporarily fixed screws.
15) Pass the power connector, the HDD connector, and the con-
troller switch connector toward you through the printer control-
ler. Fix the printer controller by hooking with the power unit
hook.
ler. Fix the printer controller by hooking with the power unit
hook.
16) Connect each connector. Fix the printer controller with three
screws (M4 x 10).
∗
Connect the connectors to the power switch so that the blue
connector is connected toward you, and the white connector in
the opposite side.
connector is connected toward you, and the white connector in
the opposite side.
17) Slide the printer controller cover and fix it with the screws.
18) Connect the I/F cables to the printer controller. Fix two I/F
cables to the I/F fixing block with the snap band at three posi-
tions.
tions.
19) Install the removed parts to the original positions.
∗
When closing the scanner unit, check that the I/F cable is
engaged with the notch section.
engaged with the notch section.
