AR-C170 (serv.man48). AR-FX10 (Fax Option) Operation Manual when installed on AR-C170M or AR-C172M - Sharp Copying Equipment User Guide / Operation Manual. Page 85

■

■

■

■ Fax receive settings

The receive settings allow you to adjust certain
parameters for receiving faxes to better suit your needs.
Settings that can be adjusted depend on the
peripheral devices installed.
The "Fax receive settings" are as follows:

● Auto receive reduce setting
● Number of calls in auto reception
● Duplex reception setting (only when the duplex

● Print style setting
● Set the telephone number for data forwarding
● Output tray setting
● Anti junk fax setting

When you receive a fax that includes the sender's
name, sender's number, and other printed
information, the received image will be slightly
larger than the standard size*. This setting lets you
select whether or not the received image is
automatically reduced before printing to fit the
standard size. Normally automatic reduction is
enabled.

* Standard sizes are sizes such as A4 and B5

(8-1/2"x11" and 8-1/2"x5-1/2").

This setting is used to select the number of rings on
which the machine automatically receives a call
and begins fax reception when the reception mode
is set to auto. (See "RECEIVING A FAX" on page
2-7.) Normally this setting is selected to "2".
The number of rings that can be set in each country
are shown in the following table.

When the duplex module is installed, you can use
this setting to select whether received documents
are printed on both sides of the paper. Normally
this setting is turned off. If turned on, received
documents will be printed on both sides of the
paper whenever the received document consists of
two or more pages of the same paper size.

This setting determines the selection condition for
paper when printing received documents. Select
one of the three conditions below. AUTO SIZE
SELECT is normally selected.
● PRINT ACTUAL SIZE CUT OFF DISABLED

The received fax image is printed at its actual
size (without dividing it onto multiple sheets of
paper). If the same size of paper or larger paper
is not loaded, the fax will be received in memory
and will not be printed until a suitable size of
paper is loaded.

● PRINT ACTUAL SIZE CUT OFF ENABLED

Each received image is printed at actual size. If
necessary, the image is split onto multiple
sheets of paper.

● AUTO SIZE SELECT

Each received image is printed at actual size
when possible. When not possible, the image is
automatically reduced before printing.

When a problem prevents the machine from printing
a received fax, the transfer function (page 3-12) can
be used to forward the received fax to another fax
machine. Use this setting to program the fax number
of the destination fax machine. Only one fax number
can be programmed (maximum of 64 digits).
If you wish to specify an F-code confidential memory
box in the destination machine, touch the [SUB
ADDRESS] key after entering the fax number to enter
a slash "/", and then enter the sub-address. Enter a
passcode as well if needed. (See steps 9 to 12 of
"STORING ONE-TOUCH KEYS" on pages 6-3 to
6-4.)

This setting is used to select the output tray for
received faxes. The trays that can be selected will
vary depending on what peripheral devices have
been installed.

If auto receive reduce is disabled, an image larger
than the standard size will be cut off. However, the
image is clearer because it is printed at the same
size as the original.

United 
Kingdom

Australia and 
New Zealand

Singapore

0 to 9

2 to 4

0 to 3

If you select "0" for the number of rings, the machine
will immediately answer and begin fax reception
without ringing in auto reception mode.
However, do not select "0" when an extension phone
is connected to the machine.
When "0" is selected, the extension phone cannot be
used to make a call.

Whale_08.fm  9 ページ  ２００４年１０月１５日　金曜日　午前１０時２４分