Read Sharp AR-337 Handy Guide online
TECHNICAL UPDATE
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS GROUP
47
VERSION 1C
MARCH 2002
ERROR CODE
Model
Fault
Advice
Cougar 2k
CE-02
Server not found. Check IP address of E-Mail or FTP server.
(AR-NS1)
(AR-NS1)
All
C1-00
Main Charge “Arching” – check MC grid is installed and fitted
correctly. Also check HVU output.
correctly. Also check HVU output.
All
E7-XX
Various E7 codes can occur if the ICU “Cooling” fan has not been
reconnected following the removal of the ICU upper cover.
reconnected following the removal of the ICU upper cover.
All
E7-00
Poor contact on PCU flashcard. Clean and re-install.
Also check the MC corona unit has been inserted correctly (MC
“arching” can cause E7 following a warming up message).
Ensure the TC Earth strap has not been damaged due to broken
lift angle (rear frame). Also check for waste toner contamination
of the MC & TC end blocks and connections.
Also check the MC corona unit has been inserted correctly (MC
“arching” can cause E7 following a warming up message).
Ensure the TC Earth strap has not been damaged due to broken
lift angle (rear frame). Also check for waste toner contamination
of the MC & TC end blocks and connections.
AR280/285/
335
E7-00
Intermittent E7-00 is corrected by the following firmware revision:-
ICU – 3.37, PCU – 3.35, OPE 3.35 or higher.
ICU – 3.37, PCU – 3.35, OPE 3.35 or higher.
All
E7-01
Image data memory trouble :-
1. The ICU Simm card is not installed.
2. Faulty ICU Simm card.
3. ICU PWB abnormality.
4. The Simm capacity is insufficient for the model.
2. Faulty ICU Simm card.
3. ICU PWB abnormality.
4. The Simm capacity is insufficient for the model.
AR280/285/
335
E7-03
Fit HDD protective sheet
(PSHEZ4685FCZZ)
to eliminate HDD
vibration. Can also cause E7-11.
Also, ensure engine firmware is v2.02 or higher (All).
Also, ensure engine firmware is v2.02 or higher (All).
All
E7-11
Check FFC1/FFC2 CCD harnesses for poor connection. Ensure
the optical mirror base is not skewed.
Also check copy lamp operation during power on for CCD
shading correction – replace lamp if necessary (not
AR280/285/335).
the optical mirror base is not skewed.
Also check copy lamp operation during power on for CCD
shading correction – replace lamp if necessary (not
AR280/285/335).
Not
AR505/507
F1-05
Incorrect timing operation of AS & PLS sensors. Check both
sensors initialise when the off-set tray reaches home position by
using Sim 3. Check the cam detection lever is fitted correctly or
not broken. (AR-FN2)
sensors initialise when the off-set tray reaches home position by
using Sim 3. Check the cam detection lever is fitted correctly or
not broken. (AR-FN2)
All
F1-08
STUHP sensor not working. Check sensor and connection CN-J
on the finisher control pwb.
on the finisher control pwb.
Not
AR505/507
F1-11
Incorrect fitting of the offset tray jamming the bundle discharge
rollers as they rotate 360 degrees after the off set tray reaches
home. (AR-FN2).
rollers as they rotate 360 degrees after the off set tray reaches
home. (AR-FN2).
Not
AR505/507
F1-14
F1-15
F1-15
Check the finisher is level – on loose or flexible flooring, the
finisher can move away from the machine for small periods.
When this happens, and error will occur due to the movement of
the off-set tray. (AR-FN2)
finisher can move away from the machine for small periods.
When this happens, and error will occur due to the movement of
the off-set tray. (AR-FN2)
AR505/507
F1-18
The lower output tray paddle roller becomes tight. Strip, remove
and lubricate the brass bearings and the shaft.
and lubricate the brass bearings and the shaft.
Click on the first or last page to see other AR-337 service manuals if exist.