Read Sharp AR-285 (serv.man2) Handy Guide online
TECHNICAL UPDATE
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS GROUP
48
VERSION 1
JANUARY 2002
ERROR CODE
Model
Fault
Advice
AR405
F1-50
Incorrect AR-FN1 finisher firmware. Upgrade to v3.12 or higher
(AR-FN1N).
(AR-FN1N).
All
F2-00
Reroute the wiring harness (PG 15/26) going to the toner
concentration sensor so the wires are not hanging in the way of
the DV guide (PG 30/7). If the harness is slack, it may scrape on
the DV guide and cause a break in the wire.
Also check the MX shafts within the DV unit are not seized and
the correct toner has been installed
(eg SF230LT1 can be installed due to similar key).
concentration sensor so the wires are not hanging in the way of
the DV guide (PG 30/7). If the harness is slack, it may scrape on
the DV guide and cause a break in the wire.
Also check the MX shafts within the DV unit are not seized and
the correct toner has been installed
(eg SF230LT1 can be installed due to similar key).
All
F2-39
Process thermistor “open circuit”.
This error will occur when the process unit is removed with the
machine still powered on.
This error will occur when the process unit is removed with the
machine still powered on.
All
F9-00
Check Sim 26-44 for correct setting if printer board is installed.
Always ensure the latest engine, printer board and network card
firmware is installed for maximum reliability when printing.
Always ensure the latest engine, printer board and network card
firmware is installed for maximum reliability when printing.
All
H3-00
Occurs when the machine enters “Pre Heat” mode.
Check and clean all thermistors and ensure all cooling fans are
working correctly.Increase the pre heat temperature setting (Sim
43) to 145-160 (firmware dependent).
Check and clean all thermistors and ensure all cooling fans are
working correctly.Increase the pre heat temperature setting (Sim
43) to 145-160 (firmware dependent).
Cougar 2k
H3-00
Intermittent H3-00 may occur following an E7-00 trouble code
(heater lamps can stay on until the maximum fuser temperature is
reached due to the loss of the fuser control). Upgrade the engine
firmware to the latest version for improved ICU/PCU
communication/control
(heater lamps can stay on until the maximum fuser temperature is
reached due to the loss of the fuser control). Upgrade the engine
firmware to the latest version for improved ICU/PCU
communication/control
All
L3-00
Fuse F702 blown – replace.
Cougar 2k
L3-00
Check scanner motor control setup in Sim 26-59. Set to 2 (2
phase motor) if engine firmware has been upgraded from v2.10
or earlier).
phase motor) if engine firmware has been upgraded from v2.10
or earlier).
All
L6-10
Polygon motor lock – replace motor or LSU.
Polygon Motors:-
AR286/336 CMOTP0848FC32
AR405
Polygon Motors:-
AR286/336 CMOTP0848FC32
AR405
CMOTP0847FC32
AR505 CMOTP0850FC32
Also check 24v supply to LSU (DC PSU Fuse F704).
Also check 24v supply to LSU (DC PSU Fuse F704).
All
PC
Check CN1 on ICU PWB.
All
U2
When replacing the ICU PWB, ensure to swap over IC22 to keep
all machine data (eg Meter Readings).
Reset with Sim 16.
all machine data (eg Meter Readings).
Reset with Sim 16.
All
U4-02
Poor interface connection between the duplex tray and machine
exit door. Refit connectors.
Also check the duplex alignment drive operation for possible
faulty PCU PWB.
exit door. Refit connectors.
Also check the duplex alignment drive operation for possible
faulty PCU PWB.
Click on the first or last page to see other AR-285 (serv.man2) service manuals if exist.