AR-280 (serv.man159). Parts Guide Correction - Corrona Wire. (WHITE) - Sharp Copying Equipment Technical Bulletin (repair manual)

ar-280 (serv.man159) technical bulletin
Model
AR-280 (serv.man159)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
49.7 KB
Type
PDF
Document
Technical Bulletin
Brand
Device
Copying Equipment / Parts Guide Correction - Corrona Wire. (WHITE)
File
ar-280-sm159.pdf
Date

Read Sharp AR-280 (serv.man159) Technical Bulletin online

PARTS GUIDE CORRECTION - CORONA WIRE
1.Model Name:
AR335, 285, 280
2.General:
There was an error found in the part code which was listed in the Parts Guide for the
transfer and separator charger wire of the TC unit. The error has been corrected.
Furthermore, the addition of points of caution to be observed during replacement
operations of the F. Transfer and separator charger wire listed in the parts 10-3, 4 of the
service manual has been carried out.
3.Description:
<1>
A correction of the part code for the transfer and separator charger wire of the TC
unit has been carried out.
38 TC Unit
P/G No.
Current parts
New parts
Parts name
Replacement cycle
Parts code
Parts code
Price
rank
38 -1
DWIR-0466CSZZ
DWIR-0550CSZZ
BQ
Charger wire
40 K (domestic)
80 K (overseas)
<2>
The points of caution to be observed during replacement operations of the
transfer and separator charger wire are as follows. These points of caution should be
added to page 10-3, 4 of the service manual, listed under F. Transfer and Separator
Charger Wire.
(1) The wire used should be the part correspondingto part code DWIR-0550CSZZ.
(2) Confirmation that the wire is not twisted or bent should be carried out.
(3) When the wire is wrapped around the charger spring, it should be wrapped at
an angle of about 60°. If the wrapping angle is too sharp it will be difficult for
the wire to unwrap, and if the wrapping angle is too wide there is a possibility
that the wire might be easily cut. (Please refer to the figure shown on the next
page.)
Sharp Electronics (UK) Ltd., Technical Services Group
Date:
2 August 1999
Model:
AR280/285/335
Ref:
016
Colour: White
Page:
1 of 2
TECHNICAL BULLETIN
(4) Wire cutters should always be used when cutting the excess length.
The remaining length of extra wire should be within 1 mm. The wire cutting operation
should be carried out so that there is no stress placed on the wrapped portion of the
wire. (Please refer to the figure shown below.)
(5) The charger wire should be stretched so that the length of the tension spring
is approximately 10±0.5 mm. (Please refer to the figure shown below.)
(6) The charger wire should lie in the V groove of the TC case.
Sharp Electronics (UK)Ltd., Technical Services Group
Approximately 60°
Within 1 mm
Scribe line
Tension spring
Charger wire
The length of the tension
spring (10
±
0.5 mm) should
be measured from the scribe line
wire of the TC case, and should
be less than 1 mm.
Page of 2
Display

Download Sharp AR-280 (serv.man159) Technical Bulletin

Here you can read online and download Sharp AR-280 (serv.man159) Technical Bulletin in PDF. AR-280 (serv.man159) technical bulletin will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AR-280 (serv.man159) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.