AR-200 (serv.man10). AR200 Operation Manual-Part 2 - Sharp Copying Equipment User Guide / Operation Manual

ar-200 (serv.man10) user guide / operation manual
Model
AR-200 (serv.man10)
Pages
10
Size
406.13 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Copying Equipment / AR200 Operation Manual-Part 2
File
ar-200-sm10.pdf
Date
Next: Sharp AR-200 (serv.man11) User Guide / Operation Manual

Read Sharp AR-200 (serv.man10) User Guide / Operation Manual online

27
ST
A
TUS
INDICA
T
ORS
1
Open the bypass tray. Lift slightly on the side cover
and slide the cover out until it stops.
2
Push gently on both sides of the front cover to open the
cover.
3
Lift the TD cartridge lock release lever and pull the
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
●
For disposal of the old TD cartridge, contact your dealer.
4
Remove the new TD cartridge from the bag. Hold the
cartridge on both sides and shake it horizontally four or
five times.
TD CARTRIDGE REPLACEMENT
If the machine detects an insufficient amount of toner being added, copying
will stop and the machine will add toner. During this time the START (
)
key indicator will blink. When sufficient toner has been added the indicator
will remain on steadily indicating that copying can be resumed. However,
if toner addition continues for a maximum of two minutes, the TD cartridge
replacement required (
) indicator will light up in addition to the START
(
) key being lighted steadily. This indicates that the toner supply is low
and a new cartridge will be needed soon. If copying is continued, the copies
will gradually become lighter until the copier stops and the TD cartridge
replacement required (
) indicator begins to blink, indicating that the
cartridge must be replaced. Replace the TD cartridge by following the
procedure below.
For best copying results, be sure to use only
SHARP products.
The package of SHARP toner has the Genuine
Supplies label.
 TD cartridge replacement
TD cartridge lock 
release lever
4 or 5 times
GENUINE SUPPLIES
28
ST
A
TUS
INDICA
T
ORS
 TD cartridge replacement
TD CARTRIDGE REPLACEMENT
5
Remove the protective cover from the TD cartridge by
unlatching three cover hooks from the holes on the
cartridge and then pulling the cover in the direction
indicated by the arrow in the illustration.
6
Gently insert the TD cartridge along the guides until it
locks in place.
If dirt or dust is adhered to the TD cartridge, remove it
before installing the cartridge.
7
Close the front cover by pushing both sides with your
hands and then close the side cover by pressing the
handle on the cover. The 
 indicator will go out.
When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
29
ST
A
TUS
INDICA
T
ORS
1
Open the bypass tray. Lift slightly on the side cover
and slide the cover out until it stops.
2
Push gently on both sides of the front cover to open the
cover.
3
Lift the TD cartridge lock release lever and pull the
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
4
Grasp the handle of the drum cartridge and gently pull
the cartridge out.
●
For disposal of the old drum cartridge, contact your dealer.
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 30,000 copies. When
the internal counter reaches approximately 29,000 copies, the drum
replacement required (
) indicator will light up indicating that replacement
of the drum cartridge will be needed soon. When the indicator begins to blink,
replace the drum cartridge by following the procedure given below.
Do not remove the protective cover on the drum portion
(black paper) of a new drum cartridge before use. The
cover protects the drum against external light.
●
For the procedure to find out how many more copies can be made before
the 30,000 mark is reached, see page 72, DRUM CARTRIDGE LIFE.
 Drum cartridge replacement
TD cartridge lock 
release lever
For best copying results, be sure to use only
SHARP products.
The package of SHARP drum cartridge has the
Genuine Supplies label.
GENUINE SUPPLIES
30
ST
A
TUS
INDICA
T
ORS
DRUM CARTRIDGE REPLACEMENT
 Drum cartridge replacement
5
Remove the new drum cartridge from the protective bag
and gently insert the lead end of the drum cartridge
along the guides.
Do not touch the surface of the drum (green portion) of
the cartridge. Doing so may cause smudges on the
copies.
6
Remove the protective cover from the drum cartridge
and then push the cartridge all the way into the copier.
7
Gently install the TD cartridge. To install the TD cartridge,
see page 27, TD CARTRIDGE REPLACEMENT.
8
Close the front cover by pushing both sides with your
hands and then close the side cover by pressing the
handle on the cover. The drum replacement required
(
) indicator will go out.
When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
Page of 10
Display

Download Sharp AR-200 (serv.man10) User Guide / Operation Manual

Here you can read online and download Sharp AR-200 (serv.man10) User Guide / Operation Manual in PDF. AR-200 (serv.man10) user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AR-200 (serv.man10) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.

Found More:

AR-200 (serv.man10) Service Manuals

Preview DownloadPagesSize
AR-200 (serv.man5) AR200 Service Manual Service Manual 23 153.55 KB
AR-200 (serv.man9) AR200 Operation Manual-Part 1 User Guide / Operation Manual 28 875.36 KB
AR-200 (serv.man11) AR200 Operation Manual-Part 3 User Guide / Operation Manual 18 216.41 KB
AR-200 (serv.man12) AR200 Operation Manual-Part 4 User Guide / Operation Manual 28 487.6 KB
AR-200 (serv.man6) Information of parts change Parts Guide 2 28.25 KB
AR-200 (serv.man7) Information of parts change To improve productivity, the L pulley has been changed. Parts Guide 2 20.3 KB
AR-200 (serv.man8) AR200 Parts Guide Parts Guide 12 400 KB
AR-200 (serv.man2) Strength increase of the grid mounting area on the MC holder rear side Specification 2 574.94 KB
AR-200 (serv.man3) Disuse of the fusing front transport sheet due to change of the side door inner frame Specification 2 892.31 KB
AR-200 (serv.man4) AR200 Specifications Specification 3 154.91 KB
AR-200 (serv.man20) Manual paper feed roller material change. Technical Bulletin 5 342.3 KB
AR-200 (serv.man21) MODIFICATION OF PAPER FEED ROLLER HOLDER ETC. TO IMPROVE PRODUCTIVITY Technical Bulletin 5 290.28 KB
AR-200 (serv.man22) MATERIAL CHANGE PAPER FEED SHEET Technical Bulletin 4 354.66 KB
AR-200 (serv.man23) Information of parts change (Righthand Door Assembly). Technical Bulletin 1 100.72 KB
AR-200 (serv.man24) Information of parts change (Duplex drive idle plate Copy lamp unit). Technical Bulletin 2 80.54 KB
AR-200 (serv.man25) Strength increase of the fusing lower frame. Technical Bulletin 2 57.91 KB
AR-200 (serv.man26) Strength increase of the boss for mounting the manual paper feeding latch pawl B. Technical Bulletin 3 934.83 KB
AR-200 (serv.man27) Parts Changes. Technical Bulletin 1 21.62 KB
AR-200 (serv.man28) Parts Change. Technical Bulletin 2 30.21 KB
AR-200 (serv.man29) Parts Change, Main Motor. Technical Bulletin 1 21.81 KB
AR-200 (serv.man30) Countermeasure against wrinkles on the copy paper or paper jam due to shrinkage of the FU felt. Technical Bulletin 2 26.84 KB
AR-200 (serv.man31) Attachment of a high temperature Caution Label. Technical Bulletin 2 106.9 KB
AR-200 (serv.man32) Change due to production stoppage of rubber for the manual paper feed roller (repeat due to incorrect information) Technical Bulletin 2 84.65 KB
AR-200 (serv.man33) Change due to production stoppage of rubber for the manual paper feed roller. Technical Bulletin 2 122.55 KB
AR-200 (serv.man34) 1. Change of the MX roller, 2. Material change of the roller arm, 3. Shape change of the delivery upper guide 20, 4. Change of the fusing connecting plate, 5. Standardisation of the parts code for the ATC sensor. Technical Bulletin 5 112.48 KB
AR-200 (serv.man35) 1. Multi frame change, 2. Shape change of the fusing cover. Technical Bulletin 2 16.54 KB
AR-200 (serv.man36) 1. Multi frame change, 2. Shape change of the fusing cover. Technical Bulletin 2 38.6 KB
AR-200 (serv.man37) Countermeasure against wideningof the screw hole of fixing the fuser unit to the intermediate frame. Technical Bulletin 2 483.51 KB
AR-200 (serv.man38) Information of parts change. 1 Fusing front PG change. 2 Cleaning blade change. 3 Roller pawl change. 4 Change of the AC switch to comply with RoHS. 5 Change of the line cable to comply with RoHS. Technical Bulletin 4 308.83 KB
AR-200 (serv.man39) Change of parts for the fusing unit. Technical Bulletin 2 35.61 KB
AR-200 (serv.man40) Replacement procedure for the polygon motor in the LSU unit. Technical Bulletin 4 310.83 KB
AR-200 (serv.man41) Information of parts change. (MF Sensor Spring, Delivery Pulley 34T) Technical Bulletin 2 359.14 KB
AR-200 (serv.man42) 128-Information of parts change. Technical Bulletin 1 9.71 KB
AR-200 (serv.man43) Correction to illustration of optical unit in parts guide. Technical Bulletin 1 80.77 KB
AR-200 (serv.man44) Countermeasure against paper jam when ejecting Technical Bulletin 2 92.81 KB
AR-200 (serv.man45) CHANGE OF PARTS (Base Plate Unit 2 Delivery Frame Unit MCU PWB) Technical Bulletin 1 26.04 KB
AR-200 (serv.man46) Countermeasure against paper jam due to deformation of the fusing upper paper guide sheet. Technical Bulletin 2 47.77 KB
AR-200 (serv.man47) Countermeasure against skewing due to gap in Tray Guide R Technical Bulletin 2 185.54 KB
AR-200 (serv.man48) Information of parts change Technical Bulletin 2 791.3 KB
AR-200 (serv.man49) Part number for Panther-series Power Switch Technical Bulletin 1 11.11 KB
AR-200 (serv.man50) Countermeasure against U2-40 trouble due to power supply noise Technical Bulletin 1 1.08 MB
AR-200 (serv.man51) New supply of EEPROM for service Technical Bulletin 1 7.2 KB
AR-200 (serv.man52) Change to shape of rear plate to prevent dislocation Technical Bulletin 1 183.13 KB
AR-200 (serv.man53) Countermeasure against manual feed paper jams, due to contamination of drive section Technical Bulletin 2 277.55 KB
AR-200 (serv.man54) Improved durability of cam transmission arm in manual paper feed unit Technical Bulletin 1 13 KB
AR-200 (serv.man55) Countermeasure against breakage of the fusing rear paper guide rib Technical Bulletin 1 115.9 KB
AR-200 (serv.man56) Countermeasure against breakage of the discharge holder claw Technical Bulletin 1 93.75 KB
AR-200 (serv.man57) Countermeasure against paper jam when ejecting paper Technical Bulletin 1 70.94 KB
AR-200 (serv.man58) Countermeasure against F1-06 errors Technical Bulletin 1 54.35 KB
AR-200 (serv.man59) Countermeasure against fall of DMC actuator Technical Bulletin 1 14.47 KB
AR-200 (serv.man60) Parts change information for PS transport roller Technical Bulletin 1 13.27 KB
AR-200 (serv.man61) Countermeasure for black stripes when using SPF, and for occurrence of E7-04 error message Technical Bulletin 2 37.56 KB
AR-200 (serv.man62) Countermeasure against skewing when feeding from cassette Technical Bulletin 1 20.88 KB
AR-200 (serv.man63) Design of feeding rollers is changed to improve quality of paper feeding Technical Bulletin 2 52.56 KB
AR-200 (serv.man64) Reprogramming service for ARFX2 facsimile option for panther - series machines Technical Bulletin 1 12.64 KB
AR-200 (serv.man65) Information of parts change (MCU PWB) Technical Bulletin 1 15.65 KB
AR-200 (serv.man66) Information of parts change (document feed) Technical Bulletin 1 13.25 KB
AR-200 (serv.man67) Correction of E7-04 error Technical Bulletin 1 12.56 KB
AR-200 (serv.man68) Parts change information (paper feeding unit process unit side door unit) Technical Bulletin 2 53.53 KB
AR-200 (serv.man69) Countermeasure against right door detection error Technical Bulletin 1 950.17 KB
AR-200 (serv.man70) Parts change information (feeding frame rollers) Technical Bulletin 1 14.07 KB
AR-200 (serv.man71) New supply of a service part (paper feed roller rubber) Technical Bulletin 1 12.43 KB
AR-200 (serv.man72) Countermeasure against abnormal noise from the 2nd transport clutch Technical Bulletin 1 33.05 KB
AR-200 (serv.man73) Version change of the maintenance (firmware download) software Technical Bulletin 1 13.34 KB
AR-200 (serv.man74) Parts change information (MCU PWB) Technical Bulletin 1 12.86 KB
AR-200 (serv.man75) Change of cassette lock claws Technical Bulletin 1 23.34 KB
AR-200 (serv.man76) New supply of service part Technical Bulletin 1 23.99 KB
AR-200 (serv.man77) Reducing white stripes on the CRU unit Technical Bulletin 1 21.38 KB
AR-200 (serv.man78) Parts change information Technical Bulletin 2 530.64 KB
AR-200 (serv.man79) New supply of fusing unit adding a cleaning felt AS Technical Bulletin 1 21.92 KB
AR-200 (serv.man80) Information about the part code of the delivery frame Technical Bulletin 1 21.9 KB
AR-200 (serv.man81) Parts change information Technical Bulletin 2 205.2 KB
AR-200 (serv.man82) New supply of fusing unit adding a cleaning felt AS Technical Bulletin 1 21.58 KB
AR-200 (serv.man83) Parts change (lens unit) Technical Bulletin 1 21.48 KB
AR-200 (serv.man84) New supply of a service parts described in AR161 200 ref 079 Technical Bulletin 1 23.39 KB
AR-200 (serv.man85) Software version upgrade of the main ROM for simplex models (Correction of jam detection error in special conditions) Technical Bulletin 1 22.59 KB
AR-200 (serv.man86) Countermeasure against folding of the corner of copying paper on duplex print Technical Bulletin 1 40.57 KB
AR-200 (serv.man87) Countermeasure against oblique feed of the cassette Technical Bulletin 1 33.04 KB
AR-200 (serv.man88) Countermeasure against soiling of upper heat roller. Technical Bulletin 2 111.83 KB
AR-200 (serv.man89) Parts change. Technical Bulletin 3 117.2 KB
AR-200 (serv.man90) Support of double feed during cassette paper feed and document double feed. Technical Bulletin 4 204 KB
AR-200 (serv.man91) Countermeasure against L4-01 (main motor lock) and paper jam. Technical Bulletin 2 345.83 KB
AR-200 (serv.man92) Change of the tonor motor.(Toner not supplied) Technical Bulletin 1 64.45 KB
AR-200 (serv.man93) Countermeasure against job separator home position detection error. Technical Bulletin 2 99.39 KB
AR-200 (serv.man94) Improvement of the manual paper feeding tray lock. Technical Bulletin 1 101.77 KB
AR-200 (serv.man95) Application of grease to the paper feed cassette rail. Technical Bulletin 1 100.39 KB
AR-200 (serv.man96) Countermeasure against breakage of the 2nd joint gear teeth. (WHITE) Technical Bulletin 2 87.92 KB
AR-200 (serv.man97) Parts change for the productivity improvement. (WHITE) Technical Bulletin 2 84.18 KB
AR-200 (serv.man98) Caution when replacing the MCU. (WHITE) Technical Bulletin 1 60.59 KB
AR-200 (serv.man99) Version upgrade of main body software. (Update of ref.068)(WHITE) Technical Bulletin 1 63.35 KB
AR-200 (serv.man100) Change of the operation instruction label. (WHITE) Technical Bulletin 2 102.41 KB
AR-200 (serv.man101) Version upgrade of the main body software. (WHITE) Technical Bulletin 1 36.58 KB
AR-200 (serv.man102) Change of the operation instruction label. (WHITE) Technical Bulletin 2 72.22 KB
AR-200 (serv.man103) Change of the shifter gear (50T). (WHITE) Technical Bulletin 2 62.9 KB
AR-200 (serv.man104) Change of the LSU unit. (WHITE) Technical Bulletin 1 36.42 KB
AR-200 (serv.man105) Parts change of the fusing unit. (WHITE) Technical Bulletin 1 49.79 KB
AR-200 (serv.man106) Supply of the paper feed roller as a service part. (WHITE) Technical Bulletin 1 126.6 KB
AR-200 (serv.man107) Material change of the fusing gear (45T). (WHITE) Technical Bulletin 1 128.41 KB
AR-200 (serv.man108) Version upgrade of the software of the main body. (WHITE) Technical Bulletin 1 102.46 KB
AR-200 (serv.man109) Parts change. (WHITE) Technical Bulletin 19 714.79 KB
AR-200 (serv.man110) Developer Unit Improvement To Correct Clearance Between MX Roller Shaft And Shaft Bearing. (WHITE) Technical Bulletin 2 89.23 KB
AR-200 (serv.man111) Change Of The Photoconductor. (WHITE) Technical Bulletin 1 61.61 KB
AR-200 (serv.man112) Fax Kit Problems. (WHITE) Technical Bulletin 2 68.58 KB
AR-200 (serv.man113) 1.Change Of The LSU Unit. 2.Change Of The Lamp Base Plate. 3.Change Of The LCD Spacer. (WHITE) Technical Bulletin 2 69.68 KB
AR-200 (serv.man114) 1.Earth Wire Treatment Of The 2nd Cassette Interface Harness. 2.Setting Change Of The Default Value Of The Preheat Transition Time Of AR200 For Europe. 3.Information About The Rear Exterior Mounting Procedure. 4.Default Setting Change Of SIM26-51 Copy Stop Setting . (WHITE) Technical Bulletin 3 140.35 KB
AR-200 (serv.man115) Satisfaction Of Energy Star. (WHITE) Technical Bulletin 2 70.51 KB
AR-200 (serv.man116) 1.Version Upgrade Of The CDROM. 2.Version Upgrade Of The PCL Firmware. 3.Release Of The Fax Program. 4.Parts Change For Better Productivity. 5.Supply Of Expanded Memory For The PCL PWB. (WHITE) Technical Bulletin 3 74.48 KB
AR-200 (serv.man117) Noisy Laser Unit. (WHITE) Technical Bulletin 1 58.08 KB
AR-200 (serv.man118) Correction To The Parts Guide. (WHITE) Technical Bulletin 2 79.58 KB
AR-200 (serv.man119) (Revision to reference 041)1.Change Of The Fusing Lower Frame. 2.Change Of The SPF Rack Cover. 3.Countermeasure Against Poor Insertion Of The Motherboard Connector. 4.Change Of The Rubber Cushion. (WHITE) Technical Bulletin 3 85.32 KB
AR-200 (serv.man120) Change Of The DV Side Sheet. (WHITE) Technical Bulletin 1 75.23 KB
AR-200 (serv.man121) Change Of The Default Values. (WHITE) Technical Bulletin 1 66.6 KB
AR-200 (serv.man122) 1.Addition Of Installation Procedure Manual And Protection Sheet. 2.Addition Of Maintenance Card. (WHITE) Technical Bulletin 2 65.93 KB
AR-200 (serv.man123) Satisfaction Of Energy Star. (WHITE) Technical Bulletin 2 70.73 KB
AR-200 (serv.man124) 1.Change Of The PSF Glass Sheet R. 2.Dimensions Change Of The PS Transport Roller. 3.Material Change Of The Copy Operation PWB. (WHITE) Technical Bulletin 3 92.52 KB
AR-200 (serv.man125) 1.Shape Change Of The OP PWB Shield And Addition Of A Shield Plate Card. 2.Shape Change Of The Copy Lamp Unit. 3.Disuse Of the Sub Blade Earth Plate. (WHITE) Technical Bulletin 2 67.58 KB
AR-200 (serv.man126) Version Upgrade Of The Main Body Software. (WHITE) Technical Bulletin 1 61.43 KB
AR-200 (serv.man127) Parts Change For Better Productivity. (WHITE) Technical Bulletin 2 68.56 KB
AR-200 (serv.man128) 1.Change Of The Fusing Lower Frame. 2.Change Of the PSF Rack Cover. 3.Countermeasure Against Poor Insertion Of The Motherboard Connector. 4.Change Of The Rubber Cushion. (WHITE) Technical Bulletin 3 85.19 KB
AR-200 (serv.man129) Correction To The Parts Guide. (WHITE) Technical Bulletin 1 123.76 KB
AR-200 (serv.man130) 1.Countermeasure Against Abnormal Noise. 2.Countermeasure Against Shifter Operation. 3.Shape Change Of The Cooling Fan Duct. (WHITE) Technical Bulletin 3 79.41 KB
AR-200 (serv.man131) 1.Change Of The Operation Panel Exterior. 2.Screw Change. (WHITE) Technical Bulletin 2 70.13 KB
AR-200 (serv.man132) Software Version Upgrade Of The Main Body. (WHITE) Technical Bulletin 1 61.73 KB
AR-200 (serv.man133) Parts Change For Better Productivity. (WHITE) Technical Bulletin 2 71.48 KB
AR-200 (serv.man134) 1.Change Of The Discharge Holder. 2.Shape Change Of The Copy Key. 3.Addition Of The Harness Protection Sheet. (WHITE) Technical Bulletin 2 85.08 KB
AR-200 (serv.man135) Parts Change For Better Productivity. (WHITE) Technical Bulletin 2 70.17 KB
AR-200 (serv.man136) Addition To The Service Manual. (WHITE) Technical Bulletin 1 65.17 KB
AR-200 (serv.man137) Correction To The Parts Guide. (WHITE) Technical Bulletin 1 65.82 KB
AR-200 (serv.man138) 1.Shape Change Of Fusing Cover. 2.Countermeasure Against Abnormal Noise. (WHITE) Technical Bulletin 2 79.7 KB
AR-200 (serv.man139) 1.Change Of Harness Treating Method. 2.Shape Change Of Separator Lever F. (WHITE) Technical Bulletin 2 114.22 KB
AR-200 (serv.man140) Parts Change For Better Productivity. (WHITE) Technical Bulletin 2 81.99 KB
AR-200 (serv.man141) 1.Shape Change Of Rear Exterior. 2.Shape Change Of MCU Fixing Plate. 3.Shape Change Of Sensor Fixing Plate And Optical Base Plate. (WHITE) Technical Bulletin 2 71.73 KB
AR-200 (serv.man142) 1.Change Of 3-Terminal Regulator. 2.Change Of Corner Frame R Re-inforce Plate. 3.Shape Change Of Delivery Tray. (WHITE) Technical Bulletin 2 70.9 KB
AR-200 (serv.man143) Corrections To The Service Manual. (WHITE) Technical Bulletin 2 280.47 KB
AR-200 (serv.man144) 1.Change Of Delivery Earth Spring A. 2.Disuse Of Fusing Front PG Adjusting Shaft. 3.Shape Change Of Base Plate Rail R. (WHITE) Technical Bulletin 2 71.6 KB
AR-200 (serv.man145) 1.Shape Change Of DMC Actuator. 2.Change Of Fron Cabinet. 3.Disuse Of Screws. (WHITE) Technical Bulletin 4 557.37 KB
AR-200 (serv.man146) New Supply Of Process Sub-unit. (WHITE) Technical Bulletin 2 65.11 KB
AR-200 (serv.man147) Countermeasure For Envelopes Postcards Feeding Failure Problem. (WHITE) Technical Bulletin 2 79.75 KB
AR-200 (serv.man148) Shape Change Of Pipe Shutter. (WHITE) Technical Bulletin 1 36.68 KB
AR-200 (serv.man149) Correction To The Parts Guide. (WHITE) Technical Bulletin 1 76.03 KB
AR-200 (serv.man150) Countermeasure Against Jam By Catching Thin Paper In The Drum. (WHITE) Technical Bulletin 2 61.84 KB
AR-200 (serv.man151) Countermeasure Against The Improper Movement Of ARTR2 (Job Separator). (WHITE) Technical Bulletin 2 95.25 KB
AR-200 (serv.man152) 1.Change Of TC BC Interface Electrode Spring. 2.Change Of MCU PWB Parts. 3.Change Of Mirror Motor. (WHITE) Technical Bulletin 2 27.21 KB
AR-200 (serv.man153) 1.Correspondence To EMI. 2.Change Of PS Roller Shaft. 3.Shape Change Of DMC Actuator. 4.Addition Of Front Cover Label. (WHITE) Technical Bulletin 1 25.54 KB
AR-200 (serv.man154) Change Of Reverse Gate. (WHITE) Technical Bulletin 1 23.5 KB
AR-200 (serv.man155) 1.Prevention Against Vibration Of Job Separator. 2.Shape Change Of Separator Lever R. 3.Shape Change Of Full Detection Lever. (WHITE) Technical Bulletin 1 26.12 KB
AR-200 (serv.man156) 1.Countermeasure Against Vertical Stripes. 2.Dry Heater Change. 3.Prevention Against Disengagement Of Bearing Due To Deformation Of Delivery Earth Plate. 4.Countermeasure Against White Stripes In The Halftone Mode. 5.Change Of LED On The Operation PWB. (WHITE) Technical Bulletin 2 41.14 KB
AR-200 (serv.man157) F5-02 Change Of Connector To That With Slider. (WHITE) Technical Bulletin 1 22.94 KB
AR-200 (serv.man158) Parts Guide Correction. (WHITE) Technical Bulletin 1 23.02 KB
AR-200 (serv.man159) Supply Of Service Unit For The Process Unit. (WHITE) Technical Bulletin 2 57.81 KB
AR-200 (serv.man160) Correction Of Flash ROM Version Update (Issue Of No.2.03). (WHITE) Technical Bulletin 3 470.4 KB
AR-200 (serv.man161) Update Of The Software Version Due To Release Of The Option Electronic Sort Board. (WHITE) Technical Bulletin 3 473.83 KB
AR-200 (serv.man162) Update Of The Software Version Due To Release Of The Option Printer Board. (WHITE) Technical Bulletin 3 688.27 KB
AR-200 (serv.man163) Supply Of Individual Parts Of Copy Lamp Unit. (WHITE) Technical Bulletin 2 61.58 KB
AR-200 (serv.man164) Correction Of Flash ROM Version Upgrade. (WHITE) Technical Bulletin 3 684.88 KB
AR-200 (serv.man165) Correction To The Parts Guide. (WHITE) Technical Bulletin 1 18.52 KB
AR-200 (serv.man166) Version 4.10 Firmware (Sent out as Fast Fact 89). Technical Bulletin 1 10.36 KB
AR-200 (serv.man167) Flash Upgrade Procedure (Sent out as Fast Facts 085) Technical Bulletin 3 325.04 KB
AR-200 (serv.man171) Countermeasure against peeling of the fusing front PG sheet Technical Bulletin 43.55 KB
AR-200 (serv.man16) AR161 200 Firmware (version 5.32) Driver / Update 240.77 KB
AR-200 (serv.man17) AR161 200 DM2000-Firmware for coin vendor Ver7.05 Driver / Update 243.42 KB
AR-200 (serv.man18) AR161 200 Firmware (version 5.29) Driver / Update 236.8 KB
AR-200 (serv.man19) AR161 200-Firmware for coin vendor Ver7.02 Driver / Update 238.96 KB
AR-200 December 2002 Handy Guide 35 1.83 MB
AR-200 (serv.man13) Panther firmware history table (FEB-04), including details of AR-PB8 firmware. FAQ 5 77.93 KB
AR-200 (serv.man14) Details of Fast Facts 100 Damage to ARSP2 ARRP1 FAQ 1 100.4 KB
AR-200 (serv.man15) AR-161,200,205 Caution in connecting AR-SP2 FAQ 1 2.75 KB
AR-200 (serv.man168) MSDS F-00841 Regulatory Data 2 12.59 KB
AR-200 (serv.man169) MSDS F-30841 Regulatory Data 2 11.41 KB
AR-200 (serv.man170) Environmental Data Sheet Regulatory Data 1 8.71 KB

Random: