Read Sharp AR-151 (serv.man3) Service Manual online
SW
No.
No.
Bit
No.
ITEM
Soft SW setting and function
Factory Setting
21
1
2
2
Record paper size
Used to set the reception document size and the report
output paper size. When set to Auto, the paper size is
automatically selected according to the data size and the
reduction ratio in reception.
output paper size. When set to Auto, the paper size is
automatically selected according to the data size and the
reduction ratio in reception.
1
1
1
3
Picture quality priority selection
Used to set the default resolution in sending.
0
4
Reserved
0
5
6
7
8
6
7
8
Number of reception start calls
Used to set the number of calls before reception in the auto
reception mode. The set range is 0 to 9 times.
reception mode. The set range is 0 to 9 times.
Number = 8
×
Bit5 + 4
×
Bit6 + 2
×
Bit7 + 1
×
Bit8 rings
Set range : 0 –9
0
0
1
0
0
1
0
22
1
2
3
4
2
3
4
Number of auto reception select
Used to set the number of calls before reception in the
manual reception mode. This setup is used as a backup
function when the external telephone does not respond. The
set range is OFF and 1 to 9 times.
manual reception mode. This setup is used as a backup
function when the external telephone does not respond. The
set range is OFF and 1 to 9 times.
Number = 8
×
Bit1 + 4
×
Bit2 + 2
×
Bit3 + 1
×
Bit4 rings
Set range : 0(= OFF), 1 –9
0
0
0
0
0
0
0
5
Reserved
0
6
7
8
7
8
Result list print
Used to set the printing conditions of the result list after
completion of communication.
completion of communication.
0
0
1
0
1
23
1
2
3
4
2
3
4
Number of recall times
Used to set the number of times of recalls when sending is
not normally completed due to busy status of the other party
or a communication error.
The set range is OFF and 1 to 14 times. For some causes
of the communication error, however, the number of times of
recalls must be set to a smaller level.
not normally completed due to busy status of the other party
or a communication error.
The set range is OFF and 1 to 14 times. For some causes
of the communication error, however, the number of times of
recalls must be set to a smaller level.
Recall Times = 8
×
Bit1 + 4
×
Bit2 + 2
×
Bit3 + 1
×
Bit4
times
Set range : 0(= OFF), 1 –14
Set range : 0(= OFF), 1 –14
0
0
1
0
0
1
0
5
6
7
8
6
7
8
Recall interval
Used to set the recall interval when a transmission is not
normally completed due to busy status of the other party or
a communication error.
The set range is 1 to 15 minutes.
normally completed due to busy status of the other party or
a communication error.
The set range is 1 to 15 minutes.
Recall Interval = 8
×
Bit5 + 4
×
Bit6 + 2
×
Bit7 + 1
×
Bit8
min
Set range : 1 –15
Set range : 1 –15
0
1
0
1
1
0
1
24
1
2
3
4
2
3
4
Remote select number
Used to select the first digit of the select request signal
when selecting from the external telephone to FAX reception.
The set range is 0 to 9.
when selecting from the external telephone to FAX reception.
The set range is 0 to 9.
Number = 8
×
Bit1 + 4
×
Bit2 + 2
×
Bit3 + 1
×
Bit4
Set range : 0 – 9
0
1
0
1
1
0
1
5
Remote reception
Used to set whether “Remote select number” + “
∗∗
” from an
external telephone is detected and switched to FAX
reception or not.
reception or not.
1
6
FAX signal reception
Used to set whether CNG signal is detected during OFF-
HOOK and switched to FAX reception or not.
HOOK and switched to FAX reception or not.
1
Bit No.
Letter
Legal
A4
AUTO
1
0
0
1
1
2
0
1
0
1
1 : Fine
0 : Standard
Bit No.
Always
Err/Tim
Send
Never
Error
6
0
0
0
0
1
7
0
0
1
1
0
8
0
1
0
1
0
1 : ON
0 : OFF
1 : ON
0 : OFF
AR-F152
9 – 26
Click on the first or last page to see other AR-151 (serv.man3) service manuals if exist.