Read Sharp AR-122E (serv.man6) Service Manual online
AR-122E/152E/153E/157E ELECTRICAL SECTION 13 - 4
(3) Image process ASIC (HG73C119HF)
a. General
The ASIC is composed of the three major blocks: the image process
section, the print control section, and the I/F section.
section, the print control section, and the I/F section.
Image process section:
With image data from the CCD PWB in the operation mode deter-
mined by the register setup, shading, AE process, input
mined by the register setup, shading, AE process, input
γ
correc-
tion, area separation, filter process, resolution conversion, zoom
process, output
process, output
γ
correction, binary conversion (error diffusion,
dither method, simple binary conversion) are performed.
Print control section:
When copying, the image-processed data are outputted to the LSU
according to the LSU writing timing. When scanning, the image
data are made into 8bit width and outputted to the I/F section
(USB).
according to the LSU writing timing. When scanning, the image
data are made into 8bit width and outputted to the I/F section
(USB).
I/F section:
Controls the DRAM which is the image data buffer, and processes
data send/receive between the USB I/F and the IEEE1284 I/F.
data send/receive between the USB I/F and the IEEE1284 I/F.
The ASIC is controlled by writing the operation mode and the neces-
sary setup values of the operation mode into the ASIC control register
before starting each operation. (For ASIC Pin configuration, refer to the
table at the end of this document.)
sary setup values of the operation mode into the ASIC control register
before starting each operation. (For ASIC Pin configuration, refer to the
table at the end of this document.)
b. ASIC (Signal table)
110
USBIN
Input
IF PWB detection signal
111
Input
NC
112
Input
NC
113
Avss
DGND
114
GND
DGND
115
/SCANSP
Output
Scan STOP signal
116
/SCANST
Output
Scan START signal
117
/TRANSST
Output
ASIC transfer signal
118
/PRINTST
Output
Print Start signal
119
SPMT3
Output
SPF motor signal
120
SPMT2/MIRCNT
Output/
Input
Input
SPF motor signal/mirror
counter
counter
121
SPMT1
Output
SPF motor signal
122
SPMT0
Output
SPF motor signal
123
GND
DGND
124
GND
DGND
125
Vcc
CPU3.3V
126
PSL
Output
Power save LED control
127
NC
128
/CS2
Output
ASIC chip select
PIN
No.
Signal code
Input/
Output
Operating
Scan start
CCD
PWB
PWB
Shading
CCD drive
AE
Resolution conversion,
Zooming, lmage
process circuit
Zooming, lmage
process circuit
Print data process circuit
DRAM control
PRINT control
DRAM
8MB or 16MB
8MB or 16MB
LSU
HSYNC
VSYNC
To CPU bus
ASIC
Image process section
I/F section
Print control section
ASIC control resistor
PIN
No.
Signal Name
IN/OUT
Connected
to
Description
1
cpu_ad7
IN
CPU
CPU address bus
2
cpu_ad6
IN
CPU
CPU address bus
3
cpu_ad5
IN
CPU
CPU address bus
4
cpu_ad4
IN
CPU
CPU address bus
5
VCC(CORE/DC)
3.3V
3.3V
Power
6
cpu_ad3
IN
CPU
CPU address bus
7
cpu_ad2
IN
CPU
CPU address bus
8
GND(CORE/DC) Power
9
cpu_ad1
IN
CPU
CPU address bus
10
sgs
OUT
Tr array IC SPF/RSPF gate
solenoid control signal
"H":ON
"H":ON
11
srrc
OUT
Tr array IC SPF/RSPF resist roller
clutch control signal
"H":ON
"H":ON
12
spus
OUT
Tr array IC SPF/RSPF document
feed solenoid control
signal "H":ON
signal "H":ON
13
spfs
OUT
Tr array IC SPF/RSPF document
transport solenoid
control signal "H":ON
control signal "H":ON
14
mrps1
OUT
Tr array IC SPF/RSPF motor
current control signal
15
mrps2
OUT
Tr array IC SPF/RSPF motor
current control signal
PIN
No.
Signal Name
IN/OUT
Connected
to
Description
Click on the first or last page to see other AR-122E (serv.man6) service manuals if exist.