AL-1456 (serv.man6). Unpacking and installation - Sharp Copying Equipment Service Manual (repair manual). Page 7

AL-1555 UNPACKING AND INSTALLATION 5 - 7

• After the installation, a message to restart your computer may be

displayed. In this case, click the "Yes" button to restart your com-
puter.

10) Connect the USB interface cable (see page 5-8).

Windows will detect the MFP and the Plug and Play screen will
appear. 

11) Follow the instructions in the Plug and Play screen that appears in

your version of Windows to begin the installation.

You have completed the installation of the software.

Before starting the installation, make sure the USB or parallel interface
cable is not connected to the MFP.

1) Insert the supplied CD-ROM into your CD-ROM drive.

2) Double-click "My Computer", and then double-click the CD-ROM

icon.

• When any of "Hardware Found", or "Found New Hardware Wiz-

ard" messages appear during the software installation, be sure
to click the "Cancel" button.

3) Double-click the "Setup" icon.

• If the language selection screen appears after you double click

the "Setup" icon, select the language you wish to use and click
the "Next" button. (Normally, the correct language is selected
automatically.)

4) Select the software packages to be installed, and then click the

"Next" button.

The software packages with checkmark on the list on the screen
will be installed.

Click the "Display README" button to show the information on the
selected package.

• In Windows 95/NT 4.0, "Button Manager" does not appear. In

Windows 98/Me/2000, do not select the "Button Manager"
checkbox. because this is not supported when using the parallel
interface.

5) The next screen appears. Make sure that the parallel interface

cable is not connected, and click "OK".

6) Check the contents of the package on the screen, and then click

the "Start" button.

The software packages to be installed will be displayed on the
screen. If inappropriate packages are displayed, click the "Back"
button to select only appropriate software packages.

7) Copying files for MFP driver installation and parallel interface setup

(This step will start if it was selected in step 4).

1. After confirming the message in the "Welcome" window, click

the "Next" button.

2. A dialog box appears asking you to verify that the USB or paral-

lel interface cable is not connected to the MFP. Make sure that
the interface cable is not connected and click the "Next" button.

3. Click the "Next" button in the dialog box to install the MFP driver

or Cancel to quit the installation.

The setup program will start to copy the files.

In Windows 2000, if the following screen appears while the files
are being copied (the message may appear more than once),
click "Yes" in Windows 2000.

4. The following screen appears. Click the "Yes" button, and then

the Model screen will appear. Select the model number that is
the same as the model name of your MFP and click the "Next"
button.

Be sure to select the displayed model number that is the same
as the MFP's model name. If they are not the same, the driver
will not be installed correctly.

5. Establish the printer settings and click the "Next" button.

Select "LPT1" for the port to be used. If "LPT1" does not appear,
it is likely that another printer or peripheral device is using
"LPT1". Check your other printers and peripheral devices, and
change the port setting as needed so no device is using "LPT1".
If you wish the MFP to be your default printer, select "Yes". If
not, select "No".

6. When the "Setup has completed gathering all necessary instal-

lation information" dialog box appears, click the "Yes" button.

The parallel interface driver is installed.

7. When the "The MFP driver installation is complete." dialog box

appears, click the "OK" button.

The Sharpdesk installer will start.

8) Begin installation of the Sharpdesk (This step will start if it was

selected in step 4).

1. After confirming the message in the "Welcome to Sharpdesk

installation" window, click the "Next" button.

2. Read the message in the "Information" window, and then click

the "Next" button.

3. When the "Choose Destination Location" window appears, click

the "Next" button.

Windows 95/NT 4.0

Windows 98/Me/2000