AL-1456 (serv.man27). Sect. 5 Making Copies - Sharp Copying Equipment User Guide / Operation Manual

al-1456 (serv.man27) user guide / operation manual
Model
AL-1456 (serv.man27)
Pages
6
Size
184.72 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Copying Equipment / Sect. 5 Making Copies
File
al-1456-sm27.pdf
Date

Read Sharp AL-1456 (serv.man27) User Guide / Operation Manual online

46
This chapter describes basic copying functions and some other copying functions.
SCAN ONCE / PRINT MANY
The copier is equipped with a 1-page memory buffer. This memory allows the copier
to scan an original once only and make up to 99 copies. This feature allows for
improved workflow, reduced operating noise from the copier and reduced wear and
tear on the scanning mechanism. This feature provides for a higher reliability.
COPY FLOW
5
MAKING COPIES
1
Make sure that paper has been loaded in the paper tray (p.15) or multi-
bypass tray (p.17), and check the paper size (p.14). 
If paper is not loaded, see page 15. If you are using the single bypass, check 
the paper size and then proceed to the next step without loading paper.
2
Place the original.
If you are using the original table, see "Using the original table" (p.47).
If you are using the SPF/RSPF, see "Using the SPF/RSPF" (p.48).
When copying onto A4 paper or a large size, pull out the paper output tray 
extension.
4 Start copying.
Press the start (      ) key.
3
Select the copy settings.
If you wish to copy using the initial settings (p.13), proceed to the next step.
To set the number of copies, see page 49.
To adjust the resolution and contrast settings, see page 49.
To enlarge or reduce the copy, see page 51.
AL-1555 model
To print on both sides of the paper, see page 52.
To change the tray used, see page 53.
If you are using the single bypass
Do not press the start (      ) key. Insert a 
sheet of paper into the single bypass.
 (Page 18)
Multiple copies are not possible
using the single bypass.
47
5
About interrupt copying
If you press the start (
) key to begin a copy job while a print job using the paper 
tray or multi-bypass tray is in progress, the copy job will begin automatically after the 
print data in the unit's memory is printed (interrupt copying). When this is done, the 
print data remaining in the computer is not sent to the unit. When the copy job ends, 
press the clear (
) key twice, or press the ON LINE key once to change the unit to 
the online state (p.31), or wait until the set auto clear time (p.55) elapses. The 
remaining print data will be sent to the unit and printing will resume. Interrupt copying 
is not possible during a print job using the single bypass.
ORIGINAL PLACEMENT 
Using the original table
1
Open the original cover/SPF/RSPF, and place the original.
2
Place an original face down on the original table. Align it with 
the original scale and the centering (
) mark. Gently close the 
original cover/SPF/RSPF.
Do not insert paper in the single bypass when a copy job from the paper 
tray is in progress. This will cause a misfeed.
If you start a print job while a copy job is in progress, the print job will 
begin when the copy job is completed.
The scanning function cannot be used while a copy job is in progress.
The original table can read up to A4 original.
Image loss 4 mm can occur at the leading and trailing edges of the 
copies. Also image loss 4.5 mm in total can occur along the other 
edges of the copies. It can be 6 mm (max.) at the trailing edge of the 
second copy of two-sided copying.
When copying a book or an original which has been folded or a 
crumpled original, press down the original cover lightly. If the original 
cover is not securely closed, the copies may be striped or blurred.
The original cover can be simply lifted straight up and reattached to 
allow copying of a large original (AL-1045)
Original scale
48
Using the SPF/RSPF
The SPF/RSPF is designed to hold up to 30 originals measuring from A5 to A4 and
weighting from 52 to 90 g/m
2
.
1
Make sure that no original is left on the original table.
2
Adjust the original guides to the size 
of originals.
3
Set the originals face up in the 
original feeder tray.
Stream feeding mode
The stream feeding mode allows easy operation of continuous copying from the 
SPF/RSPF. If the stream feeding mode has been enabled using user program No.4, 
the SPF/RSPF (
) indicator will blink approximately 5 seconds after the last 
original has been fed by the SPF/RSPF. While this indicator is blinking, any new 
originals placed in the original feeder tray will be fed and copied automatically. If the 
stream feeding mode has been disabled, the start (
) key must be pressed each 
time the originals are set even immediately after completion of a copy run from the 
SPF/RSPF. The default setting of the stream feeding mode is "ON". See "USER 
PROGRAMS" (p.55).
Before feeding originals in the original feeder tray, be sure to remove 
any staples or paper clips from them.
Before placing curled or wavy originals into the original feeder tray, be 
sure to flatten them. If not, original misfeeds may result.
The SPF/RSPF (
) indicator on the operation panel will light up. If 
this indicator does not light up, the originals are not properly set or the 
SPF/RSPF is not properly closed.
Badly damaged originals may misfeed in the SPF/RSPF. It is 
recommended that such originals be copied from the original table.
Special originals such as transparency film should not be fed through 
the SPF/RSPF, but should be placed directly on the original table.
Image loss (max. 4 mm) can occur at the leading and trailing edges of 
the copies. Also image loss (max. 4.5 mm in total) can occur along the 
other edges of the copies. It can be 6 mm (max.) at the trailing edge of 
the second copy of two-sided copying.
To stop continuous copying using the SPF/RSPF, press the clear 
(
)
 
key.
Copying using one-sided to one-sided mode (AL-1555):
Ensure that no indicator is lit among the original to copy indicators.
Original face up
49
5
SET THE COPY QUANTITY
Set the number of copies using the two copy quantity (
,
 
) keys when copying 
from the original table or copying from SPF/RSPF.
• Press the right copy quantity key to set the unit digit 
from 0 to 9. This key will not change the tens digit.
• Press the left copy quantity key to set the tens digit 
from 1 to 9.
EXPOSURE ADJUSTMENT/PHOTO COPYING
Exposure adjustment
Copy density adjustment is not required for most originals in the automatic exposure 
mode. To adjust the copy density manually or to copy photographs, the exposure 
level can be adjusted in five steps manually.
1
Press the exposure mode selector key to 
select the manual (
) mode or photo 
(
) mode.
2
Use the light (
) and dark (
) keys to 
adjust the exposure level. If exposure level 
2 is selected, the two left-handmost 
indicators for that level will light up 
simultaneously. Also, if level 4 is selected, 
the two right-handmost indicators for that 
level will light up simultaneously.
Press the clear (
) key to clear an entry if a mistake is made.
A single copy can be made with the initial setting, i.e., when "0" is 
displayed.
The copy resolution used for AUTO and manual (
) mode can be 
changed. (p.55)
Tens digit
Unit digit
Page of 6
Display

Download Sharp AL-1456 (serv.man27) User Guide / Operation Manual

Here you can read online and download Sharp AL-1456 (serv.man27) User Guide / Operation Manual in PDF. AL-1456 (serv.man27) user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AL-1456 (serv.man27) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.