AL-1456 (serv.man26). Sect. 6 Special Functions - Sharp Copying Equipment User Guide / Operation Manual

al-1456 (serv.man26) user guide / operation manual
Model
AL-1456 (serv.man26)
Pages
5 Few pages! See other manuals at the bottom of the first or last page.
Size
137.04 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Copying Equipment / Sect. 6 Special Functions
File
al-1456-sm26.pdf
Date

Read Sharp AL-1456 (serv.man26) User Guide / Operation Manual online

52
This chapter describes the special functions of this unit. Use these functions as 
needed.
ABOUT THE SPECIAL FUNCTIONS OF 
THE AL-1555
Two sided copying
When copying from the RSPF, two-side originals can be copied automatically 
without having to manually turn them over. Automatic two-sided copying can also be 
performed without using the RSPF. When copying from one-sided originals to two-
sided copies, copying orientation can be selected between Turn on Long Edge and 
Turn on Short Edge.
Making two-sided copies
1
Place the original on the original table or in the RSPF. (see 
"ORIGINAL PLACEMENT" (p.47).
2
Select two-sided copy mode.
When making two-sided copies from the original table, the paper size 
must be A4, letter. When making two-sided copies from the RSPF, 
A4, B5, A5, letter, legal, and invoice sizes can be used. Non-standard 
size paper cannot be used.
When making two-sided copies, the multi-bypass tray cannot be used.
When using two-sided invoice size originals from the RSPF, be sure 
to place them in the landscape orientation. Otherwise, an original 
misfeed will occur.
A
A
A  A
A
A
A     A
Turn on Short Edge
Turn on Long Edge
6
SPECIAL FUNCTIONS
53
6
A: When copying in a one-sided to two-sided mode:
Use the original to copy key to select the desired one-sided to two-sided 
copying mode (Turn on Long Edge or Turn on Short Edge). See the 
illustrations on page 52.
B: When copying in the two-sided to two-sided mode:
Use the original to copy key to select the two-sided to two-sided copying 
mode. The originals must be set in the RSPF before this mode can be set 
(step 3) on page 48.
C: When copying in the two-sided to one-sided mode:
Use the original to copy key to select the two-sided to one-sided copying 
mode. The originals must have been set in the RSPF in step 3 on page 48.
3
Select the copy settings. See "SET THE COPY QUANTITY" 
(p.49), "EXPOSURE ADJUSTMENT/PHOTO COPYING" (p.49), 
and "REDUCTION/ENLARGEMENT/ZOOM" (p.51).
Using the original table
If you are using the original table, copying is only possible in one sided to 
two-sided mode ("A" above).
1
Press the start (
) key.
The original is scanned into the unit's memory.
2
Place the original that you wish to copy onto the rear side of the 
paper, and press the start (
) key again.
Copying begins.
Using the RSPF
Press the start (
) key. Copying begins in the selected two-sided copy mode.
Selecting the tray
How to select the tray
1
Each time you press the tray select (
) key, the 
location indicated by the paper feed location 
indicator changes in the following order: paper 
tray 1, paper tray 2, multi-bypass tray.
2
3
4
5
A
B
C
AL-1555
A5
A4
A4
B5
A4
A5
141
86
70
54
DESCRIPTION OF SPECIAL FUNCTIONS
Toner save mode (page 54)
Reduces toner consumption by approximately 10%.
Power save modes (page 55)
The unit has two power save modes of operation: preheat mode and auto power 
shut-off mode.
Preheat mode
When the unit enters the preheat mode, the power save (
) indicator will light up 
and other indicators will remain on or off as before. In this condition, the fuser in 
the unit is maintained at a lower heat level, thereby saving power. To copy from 
the preheat mode, make desired copier selections and press the start (
) key 
using the normal copying procedure.
Auto power shut-off mode
When the unit enters the auto power shut-off mode, the power save (
) indicator 
will light up and other indicators will go out. The auto power shut-off mode saves 
more power than the preheat mode but requires a longer time before starting 
copying. To copy from the auto power shut-off mode, press the start (
) key. 
Then make desired copier selections and press the start (
) key using the 
normal copying procedure.
Auto clear (page 55)
The unit returns to the initial settings a preset amount of time after the end of copy, or 
scanner operation. This preset amount of time (auto clear time) can be changed.
Stream feeding mode (page 55)
For description of the stream feeding mode, see "Stream feeding mode" (p.48).
Resolution of AUTO & MANUAL mode (page 55)
You can set the copy resolution used for AUTO and MANUAL (
) exposure 
mode.
TONER SAVE MODE
1
Press the exposure mode selector key 
to select the manual (
) mode.
55
6
2
Press and hold down the exposure mode 
selector key for approximately 5 seconds. 
The manual (
) indicator will go out 
and the photo (
) indicator will begin to 
blink. The exposure indicator marked "5" 
will light up, indicating the standard toner 
mode is active.
3
To enter the toner save mode, press the 
light (
) key. The exposure indicator 
marked "1" will light up, indicating the 
toner save mode is selected.
4
Press the exposure mode selector key. The photo (
indicator will stop blinking and the exposure indicator marked 
"3" will light up. The toner save mode is now active.
USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or 
canceled as desired.
Setting the power save modes, auto clear time, stream 
feeding mode and resolution of AUTO & MANUAL mode
1
Press and hold down the light (
) and dark (
) keys 
simultaneously for more than 5 seconds until all the alarm 
indicators (
 , 
) blink and "
" appears in the display.
2
Use the left copy quantity (
) key to select a user program 
number (1: auto clear time, 2: preheat mode, 3: auto power 
shut-off timer, 4: stream feeding mode, 5: auto power shut-off 
mode 6: resolution of AUTO & MANUAL mode). The selected 
number will blink in the left side of the display.
3
Press the start (
) key. The entered program number will be 
steadily lit and the currently selected parameter number for the 
program will blink on the right side of the display.
4
Select the desired parameter using the right copy quantity (
key. The entered parameter number will blink on the right of the 
display.
To return to the standard mode, repeat the procedure but use the dark 
(
) key to select exposure level "5" in step 3.
Page of 5

Download Sharp AL-1456 (serv.man26) User Guide / Operation Manual

Here you can read online and download Sharp AL-1456 (serv.man26) User Guide / Operation Manual in PDF. AL-1456 (serv.man26) user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AL-1456 (serv.man26) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.