Read Sharp AL-1456 (serv.man23) User Guide / Operation Manual online
68
SPECIFICATIONS
Model
AL-1045
AL-1255
AL-1456
AL-1555
Type
Digital laser
copier,
desk-top type
copier,
desk-top type
Digital multifunctional system,
desk-top type
desk-top type
Copy/printing system
Dry, electrostatic transfer
Originals
Printer function
Available
Scanner function
—
Available
Paper tray
Paper tray (250 sheets)
Paper tray 1,2
(250 sheets x2)
(250 sheets x2)
Single bypass, Multi-bypass tray
Single bypass (1 sheet)
Multi-bypass
tray
(50 sheets)
tray
(50 sheets)
Paper output tray
100 sheets
SPF/RSPF
—
SPF
RSPF
Original sizes
Original table/
SPF/RSPF
SPF/RSPF
Max. A4
Original feed
Original table
1 sheet
SPF/RSPF
—
Up to 30 sheets
Copy/Printing size
A4 to A6 *
1
Image loss
Max. 3 mm (Original table) *
2
(SPF/RSPF) *
2
Max. 4 mm
Max. 4.5 mm *
Max. 4.5 mm *
3
Max. 6 mm *
4
Copy speed
10 pages/
min.
min.
12 pages/
min.
min.
14 pages/
min.
min.
15 pages/
min.
min.
Print speed
Max.12 pages/min.(A4)
Continuous copying/printing
Max. 99 pages subtractive counter
First-copy/print time
(Approximately)
(Approximately)
9.6 seconds
(paper:A4, exposure mode:AUTO, copy ratio:100% )
(paper:A4, exposure mode:AUTO, copy ratio:100% )
Copy ratio
Variable:25% to 400% in 1% increments (total 376 steps)
Fixed: 25%, 70% 86%, 100%, 141%, 400%
Fixed: 25%, 70% 86%, 100%, 141%, 400%
Exposure
system
system
Original table
Moving optical source, slit exposure (stationary platen)
with automatic exposure
with automatic exposure
SPF/RSPF
—
Moving original
Fusing system
Heat rollers
Development system
Magnetic brush development
Light source
Cold cathode fluorescent lamp
9
APPENDIX
69
9
*
1
Feed paper lengthwise only.
*
2
Leading and trailing edges.
*
3
Along the other edges in totals.
*
4
The trailing edge of the second (Two-sided copy mode).
*
5
Not including TD and drum cartridges.
First-copy time may differ depending on operating conditions, such as power-supply voltage and room
temperature. The values for copy speed are rounded to the nearest whole number.
temperature. The values for copy speed are rounded to the nearest whole number.
Resolution
Scanner
—
600 x 1200dpi
Copier
600 x 300dpi (Auto/Manual mode)
600 x 600dpi (Photo mode)
600 x 600dpi (Photo mode)
Printer
600dpi
Gradation
Scan
256 levels
Output
2 levels
Bit depth
1 bit or 8 bit/pixel
Sensor
Colour CCD
Scanning speed
Max. 2.88 ms/line
Memory
8 MB
16 MB
Power supply
Local voltage
±
10% (For this copier power supply, see the
name plate located on the back of the unit)
Power consumption
1000 W
Overall
dimensions
dimensions
Width
(mm)
607.6 607.6 607.6 809
Depth
(mm)
462.5 492.5 492.5 492.5
Weight (Approximately) *
5
16 kg
19 kg
19 kg
23 kg
Unit dimensions
Width (mm)
518
518
518
518
Depth
(mm)
462.5 492.5 492.5
492.5
Height
(mm)
295.6 380.4
380.4 465.4
Operating conditions
Temperature: 10°C to 30°C
Humidity: 20% to 85%
Humidity: 20% to 85%
Emulation
SHARP GDI
Interface
IEEE1284-compliant bi-directional parallel interface/USB
interface (USB1.1 Standard)
interface (USB1.1 Standard)
Noise level
Sound Power Level L
wA
(1B=10dB)
Copying: 6.0 [B], Standby: 3.7 [B]
Sound Pressure Level L
Sound Pressure Level L
pA
(bystander positions)
Copying: 46 [dB (A)], Standby: 23 [dB (A)]
Noise emission measurement in accordance with ISO 7779.
Noise emission measurement in accordance with ISO 7779.
Emission concentration
(measurement according to
RAL-UZ 62)
(measurement according to
RAL-UZ 62)
Ozone: less than 0.02 m
g
/m
3
Dust: less than 0.075 m
g
/m
3
Styrene: less than 0.07 m
g
/m
3
As a part of our policy of continuous improvement, SHARP reserves the
right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are
nominal values of production units. There may be some deviation from
these values in individual units.
right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are
nominal values of production units. There may be some deviation from
these values in individual units.
Model
AL-1045
AL-1255
AL-1456
AL-1555
70
ABOUT SUPPLIES AND OPTIONS
When ordering supplies, please use the correct part numbers as listed below.
Supply list
* Based on copying onto A4-type paper at 5% toned area
(The life of the TD cartridge which has been included in the unit at the factory is
approximately 2,000 sheets.)
approximately 2,000 sheets.)
Interface cable
Please purchase the appropriate cable for your computer.
Parallel interface cable
IEEE 1284-Shielded type bi-directional parallel interface cable (2m Max.)
USB interface cable
Shielded twisted pair cable, high-speed transmission equivalent (2m Max.)
Be sure to use only genuine SHARP parts and supplies.
For best copying results, be sure to use only SHARP Genuine
Supplies which are designed, engineered, and tested to maximize the
life and performance of SHARP copiers. Look for the Genuine
Supplies label on the toner package.
Supplies which are designed, engineered, and tested to maximize the
life and performance of SHARP copiers. Look for the Genuine
Supplies label on the toner package.
Supply
Part number
Usable life
TD cartridge
AL-110DC
Approx. 4,000 sheets *
Drum cartridge
AL-100DR
Approx. 18,000 sheets
71
9
MOVING AND STORING THE UNIT
Moving instructions
When moving the unit, follow the procedure below.
1
Turn the power switch off and remove the power cord from the
outlet.
outlet.
2
Open the side cover and front cover, in that order. Remove the
TD cartridge and close the front cover and side cover, in that
order.
TD cartridge and close the front cover and side cover, in that
order.
To open and close the side cover and front cover, and to remove the TD
cartridge, see "TD CARTRIDGE REPLACEMENT" (p.57).
cartridge, see "TD CARTRIDGE REPLACEMENT" (p.57).
3
Raise the handle of the paper tray and pull the paper tray out
until it stops.
until it stops.
4
5
Push the paper tray back into the unit.
6
Lock the scan head locking switch (p.9).
7
Close the multi-bypass tray (AL-1555) and the paper output
tray extension, and attach the packing materials and tape
which were removed during installation of the unit. See
"PREPARING THE UNIT FOR INSTALLATION" (p.8).
tray extension, and attach the packing materials and tape
which were removed during installation of the unit. See
"PREPARING THE UNIT FOR INSTALLATION" (p.8).
8
Pack the unit into the carton. See "CHECKING PACKED
COMPONENTS AND ACCESSORIES" (p.8).
COMPONENTS AND ACCESSORIES" (p.8).
Proper storage
Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight
Store paper in the wrapper and lying flat.
• Paper stored out of the wrapper or in packages standing on end may curl or get
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight
Store paper in the wrapper and lying flat.
• Paper stored out of the wrapper or in packages standing on end may curl or get
damp, resulting in paper misfeeds.
When moving this unit, be sure to remove the TD cartridge in advance.
When shipping the unit, the scan head locking switch must be locked to
prevent shipping damage.
prevent shipping damage.