AL-1456 (serv.man12). Simulation and trouble codes - Sharp Copying Equipment Service Manual (repair manual)

al-1456 (serv.man12) service manual
Model
AL-1456 (serv.man12)
Pages
15
Size
135 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Simulation and trouble codes
File
al-1456-sm12.pdf
Date

Read Sharp AL-1456 (serv.man12) Service Manual online

AL-1555 SIMULATION, TROUBLE CODES 10 - 1
[10] SIMULATION, TROUBLE CODES
1. Entering the simulation mode
To enter the serviceman simulation mode, press the keys as follows:
Clear 
 Density select 
 Clear
 Density select
To cancel the simulation mode, press the clear key.
Flow chart of entering the simulation mode
1
YES
NO
NO
YES
YES
YES
1
NO
NO
YES
Is there a sub
    code ?
Press the COPY
         key.
Press the COPY key.
The COPY QUANTITY
display blinks to indicate
"00" and the machine 
enters the ready
state for sub code input.
Enter the sub code with
the COPY QUANTITY key.
10th digit
1st digit:
Press the COPY key.
The current set adjustment
value and the counter
value are displayed on the
COPY QUANTITY 
displayed Sensor check,
etc. are displayed by the 
alarm lamps, etc. 
To change the current set
values, enter with the COPY
QUANTITY key.
10th digit:
1st digit: 
Count up of values: 
 COPY QUANTITY key
Count down of values:
 Zoom key + COPY 
  QUANTITY key
The entered value
is displayed on the
COPY QUANTITY
display.
Press the COPY
          key.
The entered value
    is registered.
Is it the
Perform the operation
according to the
simulation number.
 performed ?
Press the clear key.
All displays on the
operation panel go off, 
and the machine enters 
the ready state for
entering the main code.
Press the clear key.
End
     Is the
main code the 
     same ?
     Is the
  sub code
displayed ?
Press the clear key.
The COPY QUANTITY
display blinks to indicate
the  previously set sub
enters the ready 7 state for
sub code input. 
code, and the machine
Press the clear key.
Enter the new main
         code.
The main code is
displayed on the
COPY QUANTITY
display.
Start
Press the clear key.
Press the exposure
mode selector key.
All displays on the
operation panel go off,
and the machine enters 
he ready state for entering 
he main code.
Count up of values: 
  COPY QUANTITY key
Count down of values:
  Zoom key + COPY 
  QUANTITY key
The main code is
displayed on the
COPY QUANTITY
display.
simulation for
operation 
check? 
Is another
simulation to be
Enter the main code with
the COPY QUANTITY key.
10th digit:
1st digit:
Count up of values: 
 COPY QUANTITY key
Count down of values:
 Zoom key + COPY
 QUANTITY key
Press the clear key.
Press the exposure
mode selector key.
Within 1sec
Within 1sec
Within 1sec
AL-1555 SIMULATION, TROUBLE CODES 10 - 2
2. List of simulations
Sim 
No.
Kind of
main code
Sub 
code
Operation
01
Optical system
01
Mirror scan operation
06
Aging of mirror scanning
02
SPF Individual 
load operation
02
SPF sensor status display
03
Motor ON
04
Paper feed solenoid ON
05
Pressure release solenoid ON 
(RSPF)
06
Resist clutch ON (RSPF)
07
Gate solenoid ON (RSPF)
05
Lamp ON 
check
01
Operation panel display check
02
Fusing lamp, cooling fan operation 
check
03
Copy lamp ON
06
Machine 
individual load 
operation
01
Paper feed solenoid ON
02
Resist solenoid ON
07
Aging
01
Warm-up display and aging with jam
06
Intermittent aging
08
High voltage 
output check
01
Developing bias
02
Main charger (Grid high)
03
Grid voltage (Low)
06
Transfer charger
10
Other
None Toner motor aging
14
Trouble reset
None Cancel of troubles other than U2
16
U2 trouble 
reset
None Cancel of U2 trouble
22
Counter 
display
04
JAM total counter display
05
Total counter display
08
SPF counter display
12
Drum counter display
14
P-ROM version display
17
Copy counter display
18
Printer counter display
19
Scanner mode counter display
21
Scanner counter display
22
SPF JAM counter display
24
Special 
counter clear
01
JAM total counter clear
04
SPF counter clear
07
Drum counter clear
08
Copy counter clear
09
Printer counter clear
13
Scanner counter clear
14
SPF JAM total counter clear
15
Scanner mode counter clear
25
Main motor 
ON
01
Main motor operation check (Cooling 
fan motor rotation check)
10
Polygon motor ON
26
Various setup
01
Manual feed setup
02
(R) SPF setup
03
Second cassette setup
04
Machine duplex setup
06
Destination setup
07
Machine conditions check
20
Rear edge void setup
30
CE mark support control ON/OFF
38
Cancel of stop at drum life over
39
Memory capacity check
40
Polygon motor OFF time setup 
(Time required for turning OFF after 
completion of printing)
42
Transfer ON timing control setup
43
Side void setup
44
SPF document rear edge read setup
62
Energy-save mode copy lamp setup
63
Fan control select setup
30
Sensor 
operation 
check 
(Standard 
provision)
01
Paper sensor status display
43
Fusing 
temperature 
setup
01
Fusing temperature setup (Normal 
copy)
04
Fusing temperature setup 2
05
Fusing temperature setup in duplex 
copy
09
Setup of fusing control of postcard 
size paper
46
Exposure 
adjustment
01
Copy density adjustment (300dpi)
02
Copy density adjustment (600dpi)
18
Image contrast adjustment (300dpi)
19
γ
 table setup or AE operation mode 
setup
20
SPF exposure correction
29
Image contrast adjustment (600dpi)
31
Image sharpness adjustment
32
Copier color reproduction setup
48
Magnification 
ratio correction
01
Front/rear (main scanning) direction 
and scan (sub scanning) direction 
magnification ratio adjustment
49
01
Flash ROM program writing mode
50
Lead edge 
adjustment
01
Lead edge image position
10
Center offset adjustment
18
Memory reverse position adjustment 
in duplex copy
19
Duplex copy rear edge void 
adjustment
51
Timing 
adjustment
02
Resist quantity adjustment
53
08
SPF scan position automatic 
adjustment
61
Laser system 
operation
03
Polygon motor check 
(HSYNC output check)
63
Shading
01
Shading check
64
Self print 
01
Self print
Sim 
No.
Kind of
main code
Sub 
code
Operation
AL-1555 SIMULATION, TROUBLE CODES 10 - 3
3. Contents of simulations
Input method: Clear key 
 Exposure Select key 
 Clear key 
 Exposure Select key
Main 
code
Sub 
code
Content
01
01
Mirror scan operation
(Operation/Procedure)
1. When this simulation is executed, the mirror home position is detected.
2. When the _START key is pressed, scanning is executed at the speed corresponding to the currently set copy magnification ratio.
The copy magnification ratio can be arbitrarily set with the magnification ratio select key/zoom key.
06
Aging of mirror scanning
When the PRINT switch is pressed, the mirror base performs full scan at the speed of the set magnification ratio. After 3 sec, the mirror 
case performs full scan again. These procedures are repeated until the clear key is pressed. (When the PRINT switch is pressed once, 
the ready lamp keeps OFF.)
The status of the mirror home position sensor is displayed with the photoconductor cartridge lamp. (The lamp is ON when the mirror is 
at the home position.)
During aging, the copy lamp keeps ON.
02
02
SPF sensor status display   
ON/OFF of the sensors in the SPF can be checked with the following lamps.  
03
Motor ON  
(Operation/Procedure)  
When the start key is pressed, the SPF motor rotates for 10 sec at the speed corresponding to the currently set magnification ratio.
04
Paper feed solenoid ON  
(Operation/Procedure) 
When the start key is pressed, the SPF paper feed solenoid repeats ON (500 ms) and OFF (500 ms) 20 times.
05
Pressure release solenoid ON (RSPF)  
(Operation/Procedure) 
When the start key is pressed, the RSPF document transport solenoid (SPFS) repeats ON (500 ms) and OFF (500 ms) 20 times.
06
Resist clutch ON (RSPF)  
(Operation/Procedure)  
When the start key is pressed, the RSPF resist clutch (SRRC) repeats ON (500 ms) and OFF (500 ms) 20 times.
07
Gate solenoid ON (RSPF) 
(Operation/Procedure)  
When the start key is pressed, the RSPF gate solenoid (SGS) repeats ON (500 ms) and OFF (500 ms) 20 times.
05
01
Operation panel display check
• When the PRINT switch is pressed, all LEDs (including 7-segment LEDs) on the operation panel are lighted. (LED check mode)
• When 1Up key is pressed, the LEDs on the operation panel are lighted individually from the top left to the bottom right in sequence.
After completion of all individual lighting, all LEDs are lighted simultaneously. (The 7-segment LED lights the three-digit sections at
the same time.)
Individual lighting frequency
ON: 300ms,
OFF: 20ms
• When the CLEAR key is pressed, this simulation is terminated.
• When the PRINT switch is pressed in the LED check mode, the machine enters the Key input check mode.
“Key input check mode”
When the machine enters the Key input check mode, the value display section indicates “– – –.” Every time any key on the operat ion 
panel is pressed, the entered value is added and displayed on the value display section. However, the keys that were pressed once are 
not counted again.
• When the PRINT switch is pressed, the entered value is added and displayed for 3 sec and all the LEDs are lighted. (LED lighting
check mode)
(Note for Key input check mode)
• Press the PRINT switch at the end. (If it is pressed in the middle of the process, the entered value up to that moment is displayed for
3 sec and the machine enters the LED lighting check mode. (ALL the LEDs are lighted.))
• Multiple key inputs are ignored.
02
Fusing lamp, cooling fan operation check
When the PRINT switch is pressed, the fusing lamp repeats operations of 500ms-ON and 500ms-OFF 5 times. During that time, the 
cooling fan motor rotates.
Sensor name
Display lamp
Mirror home position sensor
OPC drum cartridge replacement lamp
Display
Sensor
Developer cartridge replacement lamp
Document set detection (SPID)
Jam lamp
SPF document transport detection (SPPD)
Photoconductor cartridge replacement lamp
SPF cover open/close detection (SDOD)
SPF jam lamp
SPF open/close detection (SDSW)
FAX document size detection
Paper size detection
AL-1555 SIMULATION, TROUBLE CODES 10 - 4
05
03
Copy lamp ON 
(Operation/Procedure) 
When the START key is pressed, the copy lamp is lighted for 5 sec.
06
01
Paper feed solenoid ON  
(Operation/Procedure) 
When the START key is pressed, the paper feed solenoid selected by the tray select key repeats ON (500ms) and OFF (500ms) 20 
times.
02
Resist solenoid ON  
(Operation/Procedure)  
When the START key is pressed, the resist solenoid (RRS) repeats ON (500ms) and OFF (500ms) 20 times.
07
01
Warm-up display and aging with jam
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. Warm-up time is counted and displayed every second on the copy quantity display.
3. After completion of warm-up, the time count is stopped and the ready lamp is lighted.
4. Press the clear key to clear the warm-up time display, set the copy quantity, and press the START key, and the machine will copy 
the set quantity repeatedly.
This simulation is canceled by turning off the power or executing any simulation which performs hardware reset.
06
Intermittent aging
(Operation/Procedure)
1. When the simulation is executed, warming up is started.
2. After completion of warm-up, the ready lamp is lighted.
3. Set the copy quantity and press the START key, and the machine will copy the set quantity repeatedly.
4. After 3 sec of the interval time from completion of copying the set quantity, the machine will resume copying.
5. The above operation 4 is repeated.
This simulation is canceled by turning off the power or executing any simulation which performs hardware reset.
08
01
Developing bias  
(Operation/Procedure)  
When the START key is pressed, the developing bias is outputted for 30 sec.
02
Main charger (Grid high)  
(Operation/Procedure) 
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage HIGH mode.
03
Grid voltage (Low)  
(Operation/Procedure)  
When the START key is pressed, the main charger output is supplied for 30 sec in the grid voltage LOW mode.
06
Transfer charger  
(Operation/Procedure)  
When the START key is pressed, the transfer charger output is supplied for 30 sec.
10
None  Toner motor aging  
(Operation/Procedure) 
When the START key is pressed, the toner motor output is supplied for 30 sec.
14
None  Cancel of troubles other than U2  
(Operation/Procedure) 
After canceling the trouble, the simulation is also automatically canceled.
16
None  Cancel of U2 trouble
(Operation/Procedure)
1. When the START key is pressed, the EEPROM total counter check sum is rewritten and the trouble is canceled.
2. After canceling the trouble, the simulation is also automatically canceled.
22
04
JAM total counter display
The display method is the same as the total count value display.
05
Total counter display  
The total count value is displayed in 3 digits X 2 times repeatedly. 
<Display example: 12345>  
08
SPF counter display
The display method is the same as the total count value display.
12
Drum counter display
The display method is the same as the total count value display.
14
P-ROM version display
The main code and the sub code of the P-ROM version is displayed on the value display section in 2 digits alternately.
The display method is the same as the total count value display.
17
Copy counter display
The display method is the same as the total count value display.
Main 
code
Sub 
code
Content
012 
Blank
345
Blank
012
0.7s
0.3s 0.7s
1.0s
0.7s
Page of 15
Display

Download Sharp AL-1456 (serv.man12) Service Manual (Repair Manual)

Here you can read online and download Sharp AL-1456 (serv.man12) Service Manual in PDF. AL-1456 (serv.man12) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AL-1456 (serv.man12) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.