AL-1045 (serv.man30). Sect. 2 Setting Up the Unit - Sharp Copying Equipment User Guide / Operation Manual

Model
AL-1045 (serv.man30)
Pages
7
Size
303.27 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Copying Equipment / Sect. 2 Setting Up the Unit
File
al-1045-sm30.pdf
Date

View Sharp AL-1045 (serv.man30) User Guide / Operation Manual online

7
2
Follow the installation procedure below to use the unit properly.
SETUP PROCEDURE
When using the unit for the first time, setup the unit following the procedure shown 
below.
*
1
If you are only using the unit for copying, skip this step.
*
2
The multi-bypass tray is only included with the AL-1555.
If the unit does not function properly during setup or use, or if a function 
cannot be used, see "TROUBLESHOOTING THE UNIT" (p.61).
1 Open the package, and make sure that all the accessories are 
supplied with the unit. (p.8)
2 Remove the protective materials. (p.9)
8 Now, you can copy (p.46), print (p.32), or scan (p.34) your 
3 Install the TD cartridge. (p.10)
4 Load the paper in the paper tray (p.15) or the multi-bypass 
tray*
. (p.17)
5 Plug the other end of the power cord into the nearest outlet.  (p.12)
6 Install the software.*
1
 (p.19)
7 Connect the interface cable*
1
 (p.45) and turn on the unit. (p.12)
2
SETTING UP THE UNIT
8
CHECKING PACKED COMPONENTS AND 
ACCESSORIES
Open the carton and check if the following components and accessories are 
included.
If anything is not included or is damaged, contact your authorized Service 
representative.
PREPARING THE UNIT FOR INSTALLATION
1
Be sure to hold the handles on 
both sides of the unit to unpack 
the unit and carry it to the 
installation location.
Drum cartridge 
(installed in unit)
Operation manual
AL-1045
AL-1255
AL-1456
AL-1555
Software CD-ROM
TD cartridge
9
2
2
Remove all pieces of tape shown in the illustration below. Then 
open the original cover/SPF/RSPF and remove protective 
materials. After that, take out the bag containing the power 
cord and TD cartridge.
3
Release the scan head locking switch.
The scan head locking switch is under the original table.
AL-1555
AL-1255
AL-1456
(AL-1555 only)
AL-1045
AL-1045
AL-1255/AL-1456/AL-1555
AL-1255/AL-1456/AL-1555
Lock
Unlock
Grasp here and turn in 
the direction of the arrow.
10
INSTALLING THE TD CARTRIDGE
1
Open the multi-bypass tray 
(AL-1555, p.17), and then 
open the side cover.
2
Remove the CAUTION tape from the front cover and remove the 
two protective pins from the fusing unit by pulling the strings 
upward one at a time.
3
Push gently on both sides of the 
front cover to open the cover.
4
Remove the TD cartridge from the bag. Remove the protective 
paper. Hold the cartridge on both sides and shake it 
horizontally four or five times. Hold the tab of the protective 
cover and pull the tab to your side to remove the cover.
CAUTION tape
Protective pins
4 or 5 times
11
2
5
Gently insert the TD cartridge 
until it locks in place while 
pushing the lock release button.
6
Close the front cover and then 
the side cover by pressing the 
round projections near the 
side cover open button.
When closing the covers, be 
sure to close the front cover 
securely and then close the 
side cover. If the covers are 
closed in the wrong order, the 
covers may be damaged.
12
POWER ON
Ensure that the power switch of the unit is in the OFF position. Insert the attached 
power cord into the power cord socket at the rear of the unit. Plug the other end of 
the power cord into the nearest outlet. Turn the power switch on the left side of the 
unit to the "ON" position. The start (
) indicator will light up and other indicators 
which show the initial settings of the operation panel will also light up to indicate the 
ready condition. For the initial settings, see the "Initial settings of operation panel" 
described on the next page.
About the scan head
The scan head lamp remains on constantly when the unit is in the ready condition 
(when the Start indicator is illuminated).
The unit adjusts the scan head lamp periodically to maintain copying quality. At this 
time, the scan head moves automatically. This is normal and does not indicate unit 
trouble.
If you use the unit in a country other than the country where the unit was 
purchased, you will need to make sure that your local power supply is 
compatible with your model. If you plug the unit into an incompatible 
power supply, irreparable damage to the unit will result.
Only insert the power cord into a properly grounded wall socket.
Do not use extension cords or power strips.
The unit will enter a power save mode once the set time has elapsed 
without any unit operation . The settings of the power save modes can 
be modified. See "USER PROGRAMS" (p.55).
The unit will return to the initial settings a preset amount of time after 
the end of copy, or scanner job. The preset amount of time (auto clear 
time) can be changed. See "USER PROGRAMS" (p.55).
13
2
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when 
the time set with the "Auto clear time" setting (p.54) elapses after a copy or scanner 
job is finished, or when the clear (
) key is pressed twice.
The initial settings of the operation panel are shown below.
When copying is begun in this state, the settings in the following table are used.
Power off methods
If not used for a certain period of time, the unit will automatically enter auto power 
shut-off mode (p.54) in order to minimize power consumption. In cases where the 
machine will not be used for a long time, turn off the power switch and remove the 
power cord from the outlet.
Copy quantity
1 copy
Exposure adjustment
Auto
Zoom
100%
AL-1555 only
Original to copy
The "Original to copy" indicator does 
not illuminate. (One-sided copying 
only)
Tray
Paper tray 1
AL-1555
A5
A4
A4
B5
A4
A5
141
86
70
"0" is displayed in the display.
13
2
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when 
the time set with the "Auto clear time" setting (p.54) elapses after a copy or scanner 
job is finished, or when the clear (
) key is pressed twice.
The initial settings of the operation panel are shown below.
When copying is begun in this state, the settings in the following table are used.
Power off methods
If not used for a certain period of time, the unit will automatically enter auto power 
shut-off mode (p.54) in order to minimize power consumption. In cases where the 
machine will not be used for a long time, turn off the power switch and remove the 
power cord from the outlet.
Copy quantity
1 copy
Exposure adjustment
Auto
Zoom
100%
AL-1555 only
Original to copy
The "Original to copy" indicator does 
not illuminate. (One-sided copying 
only)
Tray
Paper tray 1
AL-1555
A5
A4
A4
B5
A4
A5
141
86
70
"0" is displayed in the display.
13
2
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when 
the time set with the "Auto clear time" setting (p.54) elapses after a copy or scanner 
job is finished, or when the clear (
) key is pressed twice.
The initial settings of the operation panel are shown below.
When copying is begun in this state, the settings in the following table are used.
Power off methods
If not used for a certain period of time, the unit will automatically enter auto power 
shut-off mode (p.54) in order to minimize power consumption. In cases where the 
machine will not be used for a long time, turn off the power switch and remove the 
power cord from the outlet.
Copy quantity
1 copy
Exposure adjustment
Auto
Zoom
100%
AL-1555 only
Original to copy
The "Original to copy" indicator does 
not illuminate. (One-sided copying 
only)
Tray
Paper tray 1
AL-1555
A5
A4
A4
B5
A4
A5
141
86
70
"0" is displayed in the display.
13
2
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when 
the time set with the "Auto clear time" setting (p.54) elapses after a copy or scanner 
job is finished, or when the clear (
) key is pressed twice.
The initial settings of the operation panel are shown below.
When copying is begun in this state, the settings in the following table are used.
Power off methods
If not used for a certain period of time, the unit will automatically enter auto power 
shut-off mode (p.54) in order to minimize power consumption. In cases where the 
machine will not be used for a long time, turn off the power switch and remove the 
power cord from the outlet.
Copy quantity
1 copy
Exposure adjustment
Auto
Zoom
100%
AL-1555 only
Original to copy
The "Original to copy" indicator does 
not illuminate. (One-sided copying 
only)
Tray
Paper tray 1
AL-1555
A5
A4
A4
B5
A4
A5
141
86
70
"0" is displayed in the display.

Download Sharp AL-1045 (serv.man30) User Guide / Operation Manual

Here you can view online and download Sharp AL-1045 (serv.man30) User Guide / Operation Manual in PDF. AL-1045 (serv.man30) user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AL-1045 (serv.man30) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.