PN-Y475 (serv.man3). Setup Manual - Sharp Monitor User Guide / Operation Manual. Page 6

Read Sharp PN-Y475 (serv.man3) User Guide / Operation Manual online

4
E
MOUNTING PRECAUTIONS
SAFETY INSTRUCTION
•  This product is for use indoors.
•  A mounting bracket compliant with VESA specifications is 
required.
•  Since the monitor is heavy, consult your dealer before 
installing, removing or moving the monitor.
•  Mounting the monitor on the wall requires special expertise 
and the work must be performed by an authorized SHARP 
dealer. You should never attempt to perform any of this 
work yourself. Our company will bear no responsibility 
for accidents or injuries caused by improper mounting or 
mishandling.
•  Use the monitor with the surface perpendicular to a level 
surface. If necessary, the monitor may be tilted up to 20 
degrees upward or downward.
•  This monitor should be used at an ambient temperature 
between 32°F (0°C) and 104°F (40°C).  
Provide enough space around the monitor to prevent heat 
from accumulating inside.
Unit: inch [mm]
For the monitor in portrait orientation
7-7/8 [200]
2
[50]
2
[50]
2 [50]
2
[50]
2 [50]
For the monitor in landscape orientation
Unit: inch [mm]
5/16 [7]
5/16 [7]
7-7/8 [200]
2
[50]
Power LED
•  If it is difficult to provide sufficient space for any reason 
such as the installation of the monitor inside a housing, or 
if the ambient temperature may be outside of the range 
of 32°F (0°C) to 104°F (40°C), install a fan or take other 
measures to keep the ambient temperature within the 
required range.
•  Do not block any ventilation openings. If the temperature 
inside the monitor rises, this could lead to a malfunction.
•  Do not place the monitor on a device which generates heat.
•  Adhere to the following when installing the monitor in its 
portrait orientation. Failing to adhere to the following may 
cause malfunctions. 
-   Install the monitor such that the power LED is located on 
the bottom side.
-   Set the THERMAL SENSOR SETTING on the SETUP 
menu to PORTRAIT. (See OPERATION MANUAL.)
•  Use the supplied vertical sticker when you install the 
monitor in portrait orientation.
Vertical sticker 
(Operation panel)
Vertical sticker 
(Logo)
Do not remove the factory-affixed sticker but affix the 
sticker over it. Be careful not to cover the remote control 
sensor or buttons.
-   Do not use the monitor where there is a lot of dust, where 
humidity is high, or where the monitor may come into contact 
with oil or steam. Do not use in an environment where 
there are corrosive gases (sulfur dioxide, hydrogen sulfide, 
nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this 
could lead to fire.
-   Ensure that the monitor does not come into contact with 
water or other fluids. Ensure that no objects such as paper 
clips or pins enter the monitor as this could lead to fire or 
electric shock.
-   Do not place the monitor on top of unstable objects or in 
unsafe places. Do not allow the monitor to receive strong 
shocks or to strongly vibrate. Causing the monitor to fall or 
topple over may damage it.
-   Do not use the monitor near heating equipment or in places 
where there is likelihood of high temperature, as this may 
lead to generation of excessive heat and outbreak of fire.
-   Do not use the monitor in places where it may be exposed to 
direct sunlight.
-   Please be sure to constantly remove dust and garbage that 
has attached to the ventilation opening. If dust collects in the 
ventilation opening or the inside of the monitor, it may lead to 
excessive heat, outbreak of fire, or malfunction. 
Please request a cleaning of the inside of the monitor from 
an authorized SHARP servicing dealer or service center.
-   The AC outlet shall be installed near the equipment and shall 
be easily accessible.
The Power Cord
-  Use only the power cord supplied with the monitor.
-   Do not damage the power cord nor place heavy objects on 
it, stretch it or over bend it. Also, do not add extension cords. 
Damage to the cord may result in fire or electric shock.
-   Do not use the power cord with a power tap. 
Adding an extension cord may lead to fire as a result of 
overheating.
-   Do not remove or insert the power plug with wet hands. 
Doing so could result in electric shock.
-  Unplug the power cord if it is not used for a long time.
-    Do not attempt to repair the power cord if it is broken or  
malfunctioning. Refer the servicing to the service representative.
Page of 44
Display

Click on the first or last page to see other PN-Y475 (serv.man3) service manuals if exist.