Read Sharp PN-A601 (serv.man3) Service Manual online
CHAPTER 1. OUTLINE OF THE PRODUCT
PN-A601 OUTLINE OF THE PRODUCT
1 – 8
2 - 2. CONTROL KIT
■ REMOTE CONTROL SENSOR BOX
<INSTALLING PROCEDURE>
3Refer to page 2 - 8 “■ CONNECTION WITH THE CONTROL KIT
(OPTIONAL)”.
(OPTIONAL)”.
MEMO
n
When the remote control sensor box of the PN-ZR01 control kit
(optional) is connected to this monitor, you can use the bright-
ness sensor and remote control sensor of the remote control sen-
ness sensor and remote control sensor of the remote control sen-
sor box. Use when you want to establish a brightness sensor in a
different location, etc.
n
When using the brightness sensor and remote control sensor on
this monitor when the remote control sensor box is connected,
this monitor when the remote control sensor box is connected,
set CONTROL KIT SETTING to INTERNAL on the SETUP
menu.
3Refer to page 2 - 10 "2 - 3. ADJUSTMENT ITEM LIST".
3Refer to page 2 - 10 "2 - 3. ADJUSTMENT ITEM LIST".
■ REMOTE CONTROL UNIT
1 Brightness sensor
2 Remote control sensor
3 Connection cable (About 2.8m)
4 Mounting bracket
2 Remote control sensor
3 Connection cable (About 2.8m)
4 Mounting bracket
1
2
2
4
3
1 Signal transmitter
2 POWER button
3 MUTE
2 POWER button
3 MUTE
button
Turns off the volume temporarily.
Press the [MUTE] button again to turn the
sound back to the previous level.
4 VOL +/-
button
(Volume
adjustment)
Pressing
or
displays the VOLUME
menu when the menu screen is not displayed.
Press
or
to adjust the volume of the sound.
If you do not press any buttons for about 4 sec-
onds, the VOLUME menu automatically disap-
pears.
pears.
BRIGHT +/-
button
(Backlight
adjustment)
adjustment)
Pressing
or
displays the BRIGHT
menu when the menu screen is not displayed.
Press
or
to adjust the brightness.
If you do not press any buttons for about 4 seconds,
the BRIGHT menu automatically disappears.
the BRIGHT menu automatically disappears.
*
When “BRIGHTNESS SENSOR” is “ON”
or “ON: DISPLAY”, when the brightness is
adjusted “BRIGHTNESS SENSOR” will
become “OFF”.
become “OFF”.
Cursor control (
S/T/W/ X) buttons
5 DISPLAY
button
Displays monitor information. When you press
this button again, the display disappears.
When the PN-ZB01(optional) is attached, the
display changes from INFORMATION1
display changes from INFORMATION1
J
INFORMATION2
J clear display, and so on
every time you press this button.
n
The display disappears automatically after
about 15 seconds.
about 15 seconds.
n
is displayed during LAN communication.
n
If
is displayed in red, there is a duplicate
IP address.
6 MODE
button
(Color mode
selection)
selection)
Each time you press this button, the color
mode changes in the following order.
n
STD (Standard)
JVIVID J sRGB
J STD...
*
“sRGB” applies to PC input only.
sRGB is international standard of color
sRGB is international standard of color
representation specified by IEC (Interna-
tional Electrotechnical Commission).
Color conversion is made in taking account
Color conversion is made in taking account
of liquid crystal’s characteristics and repre-
sents color tone close to its original image.
1
2
3
4
5
6
6
9
8
7
LAN
LAN
Click on the first or last page to see other PN-A601 (serv.man3) service manuals if exist.