LL-T15V1. Complete - Sharp Monitor Service Manual (repair manual). Page 7

PC-UM10M

LL-T15V1

CONNECTION, ADJUSTMENT, OPERATION AND FUNCTIONS

2 – 3

Installing monitor set-up information into WindowsMe, and setting the

monitor’s ICC profile as a predetermined value.

This explanation assumes that the floppy disk drive is “A drive”.

If the “Add new Hardware Wizard” has appeared:

1.  Place the Utility Disk (provided) into the computer’s A drive.

2.  Check [Specify the location of the driver [Advanced]] and click

[Next].

3.  Check [Display a list of all the drivers in a specific location, so you

can select the driver you want.], then click [Next].

4.  When [Models] is displayed, click on [Have disk], confirm that [Copy

manufacturer’s files from:] is [A:], and click [OK].

5.  Select the monitor details from the list, then click [Next], [Next], and

[Finish]. If the “Add new Hardware Wizard” appears, repeat the

installation commands beginning from 2 above.

6.  Remove the Utility Disk from the A drive.

If the “Add New Hardware Wizard” has not appeared:

1.  Place the Utility Disk in the computer’s A drive.

2.  Click on the [Start] button. From [Settings], choose [Control Panel].

3.  Double click on [Display].

4.  Click on [Settings], [Advanced] and [Monitor].

5.  In [Options], check [Automatically detect Plug & Play monitors] and

click on [Change].

6.  Check [Specify the location of the driver [Advanced]] and click

[Next].

7.  Check [Display a list of all the drivers in a specific location, so you

can select the driver you want.] and click [Next].

8.  When [Models] is displayed, click on [Have disk], confirm that [Copy

manufacturer’s files from:] is [A:], and click [OK].

9.  Select the monitor details, then click [Next], [Next], and [Finish].

10.  Check that the monitor details are displayed, then click [Apply].

11.  Click [OK], and close the window.

12.  Remove the Utility Disk from the A drive.

■

■

■

■

Installing the monitor’s ICC profile. (If the set-up information has already

been installed, so too has the profile, and there is no need to install it.)
This explanation assumes that the floppy disk drive is “A drive”.

1.  Place the Utility Disk in the computer’s A drive.

2.  Click on the [Start] button. From [Settings], choose [Control Panel].

3.  Double click on [Display].

4.  Click on [Settings] and [Advanced].

5.  Click on [General] and from [Compatibility] select [Apply the new

display setting without restarting], then click on [Color Manage-

ment].

6.  Click [Add], and select [3 

1

/

2

 Floppy [A:]] as the file location.

7.  Choose the color profile that you would like to install, and click on

[Add].

8.  Choose the profile and click on [Set As Default].

9.  Click [OK], and close the window.

10. Remove the Utility Disk from the A drive.

• When using the ICC profile, please set the [WHITE BALANCE] to

[STD].

An arm based on the VESA standard can be attached to the monitor.
The arm must be purchased separately.

When choosing the arm to be installed please take note of the following

points.

• The arm should be compatible with the VESA standard, and there

must be a gap of 75mm 

u

 75mm between the screw holes on the sec-

tion to be attached.

•  The arm must not fall off or break off after being attached to the mon-

itor.

1.  Ensure that both the monitor and computer are switched off.

2.  Remove the AC adapter and the RGB signal cable.

3.  Press down on the stand and gently fold back the monitor.

4.  Being careful not to damage the monitor, spread out a soft cloth and

lay the monitor on it display-side down.

5. Attach the arm to the monitor with four screws.

6.  Connect the AC adapter and the RGB signal cable.

Information
The screws used to
attach the arm should be
M4 screws with a length
of 4 mm ~ 6 mm protrud-
ing from the surface to be
attached. Using any other
kind of screw may lead to
the monitor falling off or
damage to the internal
part of the monitor.

4 ~ 6 mm

Screw used to
attach arm

Arm

Part of monitor to
which arm is
attached