LL-T15S1 (serv.man9). Complete - Sharp Monitor Service Manual (repair manual). Page 7

Installing monitor set-up information into WindowsMe.

If the "Add New Hardware Wizard" has appeared:
(This explanation assumes that the floppy disk drive is "A drive")

1.

Place the Monitor Settings Adjustment Disk (provided) into the
computer’s A drive.

2.

Check [Specify the location of the driver [Advanced]] and click
[Next].

3.

Check [Display a list of all the drivers in a specific location, so
you can select the driver you want.], then click [Next].

4.

When [Models] is displayed, click on [Have Disk], confirm that
[Copy manufacturer’s files from:] is [A:], and click [OK].

5.

Select the monitor details from the list, then click [Next], [Next],
and [Finish]. If the "Add New Hardware Wizard" appears, repeat
the installation commands beginning from 2 above.

6.

Remove the Monitor Settings Adjustment Disk from the A drive.

If the "Add New Hardware Wizard" has not appeared:

(This explanation assumes that the floppy disk drive is "A drive")

1.

Place the Monitor Settings Adjustment Disk in the computer’s A
drive.

2.

Click on the [Start] button. From [Settings], choose [Control
Panel].

3.

Double click on [Display].

4.

Click on [Settings], [Advanced] and [Monitor].

5.

In [Options], check [Automatically detect Plug & Play monitors]
and click on [Change].

6.

Check [Specify the location of the driver [Advanced]] and click
[Next].

7.

Check [Display a list of all the drivers in a specific location, so
you can select the driver you want.] and click [Next].

8.

When [Models] is displayed, click on [Have Disk], confirm that
[Copy manufacturer’s files from:] is [A:], and click [OK].

9.

Select the monitor details, then click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed, then click [Apply].

11. Click [OK], and close the window.

12. Remove the Monitor Settings Adjustment Disk from the A drive.

If necessary, the screen can be adjusted as follows.

The clock, phase, H-POS (horizontal positioning) and V-POS (vertical
positioning) functions can be adjusted automatically.

Brightness of backlight can be adjusted.

Fine adjustments can be made using the On Screen Display (OSD)
Menu.

Note: All adjustments will be saved even after turning the power off.

■

All adjustment values can be returned to their original ex-factory val-
ues in one command.

1.

Press the power button to turn off the monitor power.

2.

Press the MENU button and the SELECT button simultaneously,
and while doing this press the power button (i.e. turn the power
on). When [ALL RESET] appears on the screen, the reset is
complete.

Notes:

·

While ALL RESET is displayed, the control buttons do not
function.

·

It is not possible to reset values when the adjustment lock is
in place. Remove the adjustment lock before attempting to
operate control buttons.

■

By disabling the control buttons (i.e. setting the lock) any attempted
changes to adjusted values will be voided.

1.

Press the power button to turn off the monitor power.

2.

While pressing the MENU button, press the power button (i.e.
turn the power on).
When the menu is unlocked:
[ADJUSTMENT LOCKED] will appear on the screen, and the
lock will be set.
When the menu is locked:
[ADJUSTMENT UNLOCKED] will appear on the screen, and the
lock will be removed.

Note: When the lock is in place, all buttons other than the power

button are disabled.

■

Messages displayed on the screen and OSD Menu contents can be
changed to the following languages.

English, German, French, Italian, Spanish.

1.

Turn off the monitor.

2.

Pressing the SELECT and    buttons simultaneously, press the
power button (i.e. turn the power on). 
The Language Selection Menu (LANGUAGE) will be displayed
on the screen.

3.

Use the SELECT button to choose a language.

4.

Press the MENU button.
The setting is complete. From now, messages and adjustment
menus will be displayed in the chosen language.