Read Sharp R-895M (serv.man7) Service Manual online
R-895M - 21
Pin No.
Signal
I/O
Description
26
P40
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G7 line key on matrix is touched.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G7 line key on matrix is touched.
27
P77
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G6 line key on matrix is touched.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G6 line key on matrix is touched.
28
P76
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G5 line key on matrix is touched.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G5 line key on matrix is touched.
29
P75
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G4 line key on matrix is touched.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G4 line key on matrix is touched.
30
P74
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G3 line key on matrix is touched.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G3 line key on matrix is touched.
31
P73
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G2 line key on matrix is touched.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G2 line key on matrix is touched.
32
P72
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G1 line key on matrix is touched.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G1 line key on matrix is touched.
33
P71
IN/OUT
Terminal not used.
34
P70
IN
Connected to VC.
35
RESET
IN
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily
set to “L” level the moment power is applied, at this time the LSI is reset. Thereafter
set at “Hµ…level.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily
set to “L” level the moment power is applied, at this time the LSI is reset. Thereafter
set at “Hµ…level.
36
XCIN
IN
Connected to VC.
37
XCOUT
OUT
Terminal not used.
38
XIN
IN
Internal clock oscillation frequency input setting.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit
with respect to XOUT terminal.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit
with respect to XOUT terminal.
39
XOUT
OUT
Internal clock oscillation frequency control output.
Output to control oscillation input of XIN.
Output to control oscillation input of XIN.
40
VSS
IN
Power source voltage: -5V.
VC voltage of power source circuit input.
VC voltage of power source circuit input.
41
P27
OUT
Bottom heating element driving signal.
To turn on and off the relay (RY4). “L” level during grill
cooking, convection cooking or dual cooking, “H”
level otherwise. The heater relay turns on and off
within a 54 second time base in accordance with the
special program in LSI.
To turn on and off the relay (RY4). “L” level during grill
cooking, convection cooking or dual cooking, “H”
level otherwise. The heater relay turns on and off
within a 54 second time base in accordance with the
special program in LSI.
42
P26
OUT
Convection motor driving signal.
To turn on and off shut-off relay (RY7). “L” level
during convection or dual cooking, “H” level otherwise.
(Relay RY7 does not turn on at preheating mode.)
To turn on and off shut-off relay (RY7). “L” level
during convection or dual cooking, “H” level otherwise.
(Relay RY7 does not turn on at preheating mode.)
43
P25
OUT
Fan motor driving signal.
To turn on and off the fan motor relay (RY6).
“L” level during cooking, or for a while after
convection or dual cooking. “H” level otherwise.
To turn on and off the fan motor relay (RY6).
“L” level during cooking, or for a while after
convection or dual cooking. “H” level otherwise.
44
P24
OUT
Terminal not used.
45
P23
OUT
Touch control transformer driving signal.
To turn on and off the shut off relay (RY5). If the oven has not been used for more
than 2 minutes, the relay RY5 will be turned off. The relay RY5 will be turned on
when the oven door is opened and closed.
To turn on and off the shut off relay (RY5). If the oven has not been used for more
than 2 minutes, the relay RY5 will be turned off. The relay RY5 will be turned on
when the oven door is opened and closed.
ON
OFF
During
cooking
L
GND
H.
(Grill, Convection, Dual )
ON
OFF
During
cooking
L
GND
H.
( Convection or Dual cooking )
ON
OFF
During cooking, or for a while
after convection or dual cooking.
L
GND
H.
The I/O signal of the LSI are detailed in the following table.
DESCRIPTION OF LSI
Click on the first or last page to see other R-895M (serv.man7) service manuals if exist.