Read Sharp R-795M (serv.man8) Service Manual online
R-795M-
19
1
C1
IN
Terminal not used.
2
VL1
IN
Power source voltage input terminal.
Standard voltage for LCD.
Standard voltage for LCD.
3
AN7
IN
Terminal to change the on timing of the cook relay (RY2).
4-5
AN6-AN5
IN
Heating constant compensation terminal.
6
AN4
OUT
Terminal not used.
7
AN3
IN
Temperature measurement input: OVEN THERMISTOR.
By inputting DC voltage corresponding to the temperature detected by the
thermistor, this input is converted into the temperature by the A/D converter built
into the LSI.
By inputting DC voltage corresponding to the temperature detected by the
thermistor, this input is converted into the temperature by the A/D converter built
into the LSI.
8
AN2
IN
Input signal which communicates the door open/close information to LSI.
Door closed; “H” level signal.
Door opened; “L” level signal.
Door closed; “H” level signal.
Door opened; “L” level signal.
9
AN1
IN
Heating constant compensation terminal.
10
AN0
IN
Terminal to change functions to the Models.
11
P57
OUT
Timing signal output terminal for temperature measurement(OVEN
THERMISTOR).
“H” level (GND) : Thermistor OPEN timing.
“L” level (-5V) : Temperature measuring timing. (Oven cooking)
THERMISTOR).
“H” level (GND) : Thermistor OPEN timing.
“L” level (-5V) : Temperature measuring timing. (Oven cooking)
12
P56
OUT
Terminal not used.
13
P55
OUT
Timing signal output terminal for temperature measurement(OVEN
THERMISTOR).
“H” level (GND) : Thermistor OPEN timing.
“L” level (-5V) : Temperature measuring timing. (Oven cooking)
THERMISTOR).
“H” level (GND) : Thermistor OPEN timing.
“L” level (-5V) : Temperature measuring timing. (Oven cooking)
14
P54
OUT
Terminal not used.
15
P53
IN
Signal coming from touch key.
When any one of G12 line keys on key matrix is touched, a corresponding signal
from P40, P41, P72, P73, P74, P75, P76 and P77 will be input into P53. When no
key is touched, the signal is held at “L” level.
When any one of G12 line keys on key matrix is touched, a corresponding signal
from P40, P41, P72, P73, P74, P75, P76 and P77 will be input into P53. When no
key is touched, the signal is held at “L” level.
16
P52
IN
Signal similar to P53.
When any one of G11 line keys on key matrix is touched, a corresponding signal
will be input into P52.
When any one of G11 line keys on key matrix is touched, a corresponding signal
will be input into P52.
17
P51
IN
Signal similar to P53.
When any one of G10 line keys on key matrix is touched, a corresponding signal
will be input into P51.
When any one of G10 line keys on key matrix is touched, a corresponding signal
will be input into P51.
18
P50
IN
Signal similar to P53.
When any one of G9 line keys on key matrix is touched, a corresponding signal will
be input into P50.
When any one of G9 line keys on key matrix is touched, a corresponding signal will
be input into P50.
19-22
P47-P44
IN/OUT
Terminal not used.
23
TOUT
OUT
Signal to sound buzzer.
A: Tact switch touch sound.
B: Completion sound.
C: When the temperature of the oven cavity
A: Tact switch touch sound.
B: Completion sound.
C: When the temperature of the oven cavity
reaches the preset temperature in the
preheating mode, or when the
preheating hold time (30 minutes) is
elapsed.
preheating mode, or when the
preheating hold time (30 minutes) is
elapsed.
24
INT2
IN
Signal to synchronized LSI with commercial power source frequency(50Hz).
This is basic timing for time processing
of LSI.
This is basic timing for time processing
of LSI.
25
P41
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G8 line key on matrix is touched.
Signal applied to touch-key section. A pulse signal is input to P50-P53 terminal
while one of G8 line key on matrix is touched.
Pin No.
Signal
I/O
Description
A
B
C
H : GND
L
0.1 sec.
2.0 sec.
1.0 sec.
1.0 sec.
20 msec.
H : GND
L (-5V)
DESCRIPTION OF LSI
The I/O signal of the LSI are detailed in the following table
Click on the first or last page to see other R-795M (serv.man8) service manuals if exist.