Read Sharp R-27STM (serv.man3) User Guide / Operation Manual online
4
INSTALLATION
WARNING:
Inspect the Oven:
• Check the oven carefully for damage
• Check the oven carefully for damage
before and regularly after installation.
• Make sure the door closes properly, that
it is not misaligned or warped.
• Check the hinges and door safety latches
are not broken or loose.
• Ensure the door seal and sealing surfaces
are not damaged. If the door or door
seals are damaged, the oven must not be
operated until it has been repaired by a
competent person.
seals are damaged, the oven must not be
operated until it has been repaired by a
competent person.
• Inspect the oven interior and door for
dents.
IMPORTANT:
If any damage is apparent, do not operate
If any damage is apparent, do not operate
the oven in any way, until it has been
repaired by a SHARP trained engineer.
repaired by a SHARP trained engineer.
1. Remove all packing materials including the
feature sticker (if applicable). Do not remove
the plastic film from the inside of the oven
window as this protects it from dirt. The
waveguide cover prevents food and grease
from entering the waveguide area where it
could cause damage. DO NOT REMOVE
THE WAVEGUIDE COVER.
the plastic film from the inside of the oven
window as this protects it from dirt. The
waveguide cover prevents food and grease
from entering the waveguide area where it
could cause damage. DO NOT REMOVE
THE WAVEGUIDE COVER.
2. Place oven on a secure, level surface.
Ensure it is strong enough to take the oven
weight, plus the heaviest item likely to be
cooked in the oven.
weight, plus the heaviest item likely to be
cooked in the oven.
3. The
minimum
height of free space
necessary above the
top surface of the
oven is 15cm.
necessary above the
top surface of the
oven is 15cm.
4. Do not place the oven where heat, moisture
or high humidity are generated, (for example,
near or above a conventional oven) or near
combustible materials (for example, curtains).
Do not block or obstruct air vent openings.
Do not place objects on top of the oven.
near or above a conventional oven) or near
combustible materials (for example, curtains).
Do not block or obstruct air vent openings.
Do not place objects on top of the oven.
5. Make sure the power supply cord is undamaged
(See “ELECTRICAL CONNECTION” below).
Do not allow the power supply cord to
run over any hot or sharp surfaces, such
as the hot air vent area at the top rear of
the oven.
Do not allow the power supply cord to
run over any hot or sharp surfaces, such
as the hot air vent area at the top rear of
the oven.
6. The socket must be readily accessible so that it
can be easily unplugged in an emergency.
7. Do not use the oven outdoors.
BUILDING-IN-KIT.
No built-in kit is available for this oven.
This oven is designed to be used on a countertop
only. Do not place the oven in a cabinet.
No built-in kit is available for this oven.
This oven is designed to be used on a countertop
only. Do not place the oven in a cabinet.
ELECTRICAL CONNECTION.
• Do not allow water to come into contact with
the power supply cord or plug.
• Insert the plug properly into the socket.
• Do not connect other appliances to the same
• Do not connect other appliances to the same
socket using an adaptor plug.
• If the power supply cord is damaged, it must be
replaced by a Sharp approved service facility or a
similarly qualified person to avoid a hazard.
similarly qualified person to avoid a hazard.
• When removing the plug from the socket always
grip the plug, never the cord as this may damage
the power supply cord and the connections inside
the plug.
the power supply cord and the connections inside
the plug.
• If the plug fitted to your oven is a rewireable type
and in the event of the socket outlet in your home
not being compatible with the plug supplied,
remove the plug properly (do not cut off).
not being compatible with the plug supplied,
remove the plug properly (do not cut off).
• If the plug fitted to your oven is a non-rewirable
type and in the event of the socket outlet in
your home not being compatible with the plug
supplied, cut-off the mains plug.
your home not being compatible with the plug
supplied, cut-off the mains plug.
• Refit with a suitable type, observing the wiring
code given in `To replace the mains plug’ on page
37.
37.
15cm
R-27STM.indd 4
R-27STM.indd 4
8/1/08 5:19:01 PM
8/1/08 5:19:01 PM
Click on the first or last page to see other R-27STM (serv.man3) service manuals if exist.