VENTA PRO V3 (serv.man45). Version History (Bugs and Specification changes) Up to Venta Pro V3.1.993 - Sharp EPOS Driver / Update

venta pro v3 (serv.man45) driver / update
Model
VENTA PRO V3 (serv.man45)
Pages
19
Size
128.09 KB
Type
PDF
Document
Driver / Update
Brand
Device
EPOS / Version History (Bugs and Specification changes) Up to Venta Pro V3.1.993
File
venta-pro-v3-sm45.pdf
Date

Read Sharp VENTA PRO V3 (serv.man45) Driver / Update online

Venta Pro V3.1.993 VPM V1.2.199 
 
Version History (Bugs and Specification changes) 
(See the V3 supplementary manual for programming details) 
 
26/01/11   
 
 
249 
Standard Hotel Interface - $ITEM line had been incorrect from introduction of V5 
in 12-02-2002 until 29-04-2010. For compatibility a new setting can be used 
HOTELSTDV5_OLD=1 
 
 
248 
When using a training server and splitting bills only the main table could be 
cashed off, now all splits can be cashed off. 
 
 
247 
YesPay and refunds - the payment amount in payment record after completion 
was not being made negative (payment.amnt); Cashrsp reported positive 
payments (Reverse tran was OK)
 
 
 
246 
Applying subtotal discounts didn't examine discountability of item discounts. 
They now do, but will only apply to item discounts whose parent product are also 
Correspondingly discountable. 
 
 
245 
Spurious discount by line values appearing in CashRsp. Now fixed 
 
 
244 
Changes made to cash drawer switch detection for UP-5500 
 
 
243 
Problem with discount calculations now fixed. 
 
 
242 
Active Tables were sometimes slow updating table status. 
fixed 
 
 
17/11/10 
Venta Pro V3.1.979 VPM V1.2.199 
 
241 
Feature Added 
Allow big change/payment screen for payment method Cheque.
 
 
 
240 
Feature Added 
Previously when listing the outstanding credit card transactions on the Chip and 
Pin terminal within the ‘Get Bill’ list, the transactions where displayed as ‘Tab’ 
(table) number or ‘Srv’ (Server) number. 
It is now possible to display the outstanding credit card transaction using the 
following combination of the till number and appended to this the last 3 digits of 
the transaction number, e.g. on till 4 it could be 4012 
 
 
239 
Feature Added 
Currently when applying discounts any subtotal discount applied are always 
applied to the new sales amount which may have included other discounts, three 
new settings relating to whether subsequent discounts in a transaction are 
applied to other promos or not, have now been added. 
 
 
238 
Feature Added 
When using Mix and Match with ‘Apply promotion’ set as the action, the offer 
may depend on the order of item entry, i.e. discount applied to 
items at point where last bucket was triggered. Using the new setting below the 
trigger will always be the dearest items matching bucket, rather than the first 
items. This feature is not enabled by default and must be activated by adding the 
following setting to the c:\vpro\data\till001\s2001.ini file 
 
MMPromoPlus=1 
 
 
237 
Set base directory C:\Vapp as default! So command line /bC:\Vapp not required 
 
 
236 
Micros - prevent non-numeric or oversized fields: 
Note money fields were filled with * before if too big - now it's '0' 
Numeric fields are replaced by 0; text fields truncated. 
 
 
235 
After OKing a zero total after subtotal, 'create pr-load error' could occur. 
Now fixed 
 
 
234 
When a tran with 0 total is subtotalled and closed, its sales session values were 
not being updated. Fixed 
 
 
233 
Setting covers in Flooredit program wasn't updating when covers entered in 
Venta. Now showing in Floor View 
 
 
232 
Deposit could be used twice for payment within one transaction (leading to error 
604 but the transaction was finalised). Now fixed. 
 
 
231 
Big payment change screen - sometimes exits immediately. 
Possibly caused by mechanical microswitch bounce. Software now double 
checks. 
 
 
230 
Error correct on first item in table tran didn't correctly reopen a new transaction 
 
 
13/08/10 
Venta Pro V3.1.938 VPM V1.2.198 
 
 
 
229 
Feature Added  
Commidea – Ocius Bill Manager 
 
 
228 
Feature Added  
Commidea - Ocius direct connection  
 
 
227 
Feature Added 
Commidea Ocius II has a new option to choose tran no. as source for the bill ref 
 
 
226 
Feature Added  
Printing PLU/EAN on receipt 
 
 
225 
Feature Added  
Print to Kitchen Printer via table only 
 
 
224 
Feature Added 
New settings relating to whether subsequent discounts in a transaction are 
applied to other promos or not have been added 
 
There is a setting in VPM – Configure – System Configuration – More – Legacy 
Mode, this defaults to enabled and will work as it does now. 
With this setting unchecked then a combination of the 2 settings within 
promotions can be used 
 
Apply to other promos (this allows this promotion to be able to be applied to other 
promotions) 
Discountable (this allows this promotion to be discountable)
 
 
 
223 
Pole display not working, now fixed uses Com port 8 
 
 
222 
If you open a table on one till then perform an item split and then sign off. Then 
sign on to a different till with different server and try to open the table. You are 
prompted for which split to open. The second split (table 1.1) opens ok but if you 
try to open the first split it says “Table 1 is open at Till 1”. Now fixed 
 
 
221 
Refunds are counted as -ve quantity for dept/group report 
 
 
220 
When overtendering on a payment set as change occasionally the transaction 
would not treat the overtender amount as change, now fixed 
 
 
219 
Refund display stayed on after selling refund item. It was not active however 
unless next item was a child item
 
 
 
218 
When using the 86 feature, when it reaches zero it displays zero, but if you logoff 
and then go back to that product it doesn’t show any indication that there are 
none left. Now fixed 
 
 
217 
When refunding via post to room the .POS file was in correct, now fixed.  
 
 
216 
Manual-entry markdowns were disappearing from cash reports, now fixed 
 
 
215 
Hanging on Alt-F10 Exit, now fixed 
 
 
26/03/10 
Venta Pro V3.1.895 VPM V1.2.193 
 
 
214 
Feature Added 
 
It is now possible to turn off the Fixed Exit key at the bottom of the all the screens 
/ bottom function bar 
Two new control functions can be used within a macro C60 (Turns the fixed exit 
key off) and C61 (turns exit on) a use for this is as part of an open table/KP hold 
macro detailed below 
 
Table# and KP Hold          C60 F2 C70 
KP Go and Exit                  F71 C61 C10 
 
213 
Fixed File folder browsing within VPM – Systems Configuration – Fixed file 
export caused application error, now fixed 
 
 
212 
PLU Search by description cause order printing to be stopped, now fixed 
 
 
211 
Product Search by description had problems with embedded apostrophes, now 
fixed 
 
 
11/02/10 
Venta Pro V3.1.885 VPM V1.2.191 
 
 
 
210 
Venta Pro V3 now supports multiple displays, e.g. on the 9900 the inbuilt display 
(no printer config is needed) and an external POSLIGNE OCD 100 Usb display 
'OCD-100' (printer config). 
 
 
209 
Feature Added 
 
For Guestline Reslynx integration Subtotal Discounts are now calculated by item 
allowing the .POS file to show the discount that has been applied to each item. 
In VPM – External Interfaces CashRSP v9 and also Hotel(STD)vers=6 are 
required. 
 
To activate this special mode, use s2001.ini setting on each machine. 
PROMOCALCBYITEM=1 
 
The following setting works for discounts and surcharges; if you want discounts 
only use the setting above. 
PROMOCALCBYITEMDISCOUNT=1 
 
 
 
208 
Feature Added 
 
Micros. If 'Include Tax' not selected, it is now possible to use tax fields 1-4 for 
sales totals groups 5-8 
 
 
207 
Feature Added 
 
It is now possible to print the graphical logo footer on the Bill if the logo2= 1c 70 2 
0 is placed in the receipt printer section of the printer.def 
 
 
206 
When cancelling a credit card payment an authority prompt is displayed, if a 
swipe card containing details of a server with the correct authority is swiped, it 
does not do anything. If the server and password are entered manually it works 
fine. Now fixed 
 
 
205 
With 3 offer groups and 2 mix and match promotions.  Both the mix and match 
promotions are set to selling price by plu. 
The promotions will work fine, the problem is that in VPM they both show the 
same PLU within the Mix and Match Action, now fixed 
 
 
204 
A transaction in Pay State on till could be opened from another till. Now fixed 
 
 
203 
This version will now allow a server timeout in the payment screen - provided no 
part payments have been entered. 
 
 
202 
When pressing Exit in the payment screen, after a part payment used to just 
reverse the payment and exit. You now have to confirm this is what you want to 
do. 
 
 
15/10/09 
Venta Pro V3.1.866 VPM V1.2.189
 
 
 
201 
Feature Added 
 
To allow CASHRSP items with 0 price to be included in the cashrsp the new 
setting can be added to the s2001.ini file 
CASHRSPONZEROPRICE=1 
 
 
200 
Improvements within the communication process when eft files are being 
deleted. Using Yespay and Commidea Ocius 
 
 
199 
If you Open table 1 from the active tables list on the handheld and then select the 
manual status change 'Main Course' then send the order it changes the table 
status to main course on both the till and the handheld. If you log off the hand 
held and back on the table status on both HHT and Till changes back to unused. 
Now fixed 
 
 
198 
When manually changing the status of a table on the handheld it says no product 
is associated with PLU 100000003. Now fixed 
 
 
197 
When using Priority kitchen printing the follow-on items were not being shown as 
priority items on the KP. Fixed 
 
 
196 
When performing a mix and match promotion ‘cheapest item free’ an extra free 
item is shown on the screen to denote that an item has been deducted, but this 
item was also being sent through to the cashrsp file and affecting the stock. 
Fixed 
 
 
Page of 19
Display

Download Sharp VENTA PRO V3 (serv.man45) Driver / Update

Here you can read online and download Sharp VENTA PRO V3 (serv.man45) Driver / Update in PDF. VENTA PRO V3 (serv.man45) driver / update will guide through the process and help you recover, restore, fix, disassemble and repair Sharp VENTA PRO V3 (serv.man45) EPOS. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.