UP-3515 (serv.man8). UP3515 installation Manual - Sharp EPOS User Guide / Operation Manual

up-3515 (serv.man8) user guide / operation manual
Model
UP-3515 (serv.man8)
Pages
10
Size
5.08 MB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
EPOS / UP3515 installation Manual
File
up-3515-sm8.pdf
Date

Read Sharp UP-3515 (serv.man8) User Guide / Operation Manual online

CODE : 00Z
CONTENTS
 
INSTALLATION MANUAL
Parts marked with "! " are important for maintaining the safety of the unit. Be sure to replace these parts with specified ones
for maintaining the safety and performance of the unit.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UP3515VIME
LEAD-FREE SOLDER MODEL
POS TERMINAL
 MODEL
UP-3515
      
     
(For “V” version)
LEAD-FREE SOLDER
1. PORT CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1
2. INSTALLING THE INTEGRATED REAR DISPLAY
(UP-I20DP)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1
3. INSTALLING THE REMOTE POLE DISPLAY
(UP-P20DP/DPB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
4. INSTALLING THE DRAWER UNIT
(ER-03DW/ER-03DWB7/ER-04DW/ER-56DWB3)  . . . . . . . . . . . .  4
5. CONNECTING THE LAN CABLE . . . . . . . . . . . . . . . . . . . . . . . . .  4
6. CONNECTING THE RS232 DEVICE  . . . . . . . . . . . . . . . . . . . . . .  4
7. INSTALLING THE EXPANSION RAM BOARD. . . . . . . . . . . . . . .  4
8. ACCESSORY ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
AVOID: SHORT-CIRCUITING THE BATTERY TERMINALS.
KEEP THE BATTERY AWAY FROM FIRE. 
* WHEN DISPOSING THE BATTERY, FOLLOW THE LOCAL 
RULES AND REGULATIONS. 
“BATTERY DISPOSAL”
THIS PRODUCT CONTAINS NICKEL-METAL HYDRIDE BATTERY.
THIS BATTERY MUST BE DISPOSED OF PROPERLY.
REMOVE THE BATTERY FROM THE PRODUCT AND CONTACT FEDERAL OR 
STATE ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND 
DISPOSAL OPTIONS.
■  LEAD-FREE SOLDER
The PWB’ s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The
alphabet following the LF mark shows the kind of lead-free solder. 
Example:
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a breakdown or an accident. 
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use soldering iron is
recomended. 
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is inferior to
conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed the heat-resistive tem-
perature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is confirmed. 
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.  
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after com-
pletion of soldering work. 
If the soldering iron tip is discolored black during soldering work, clean
and file the tip with steel wool or a fine filer. 
5mm
Lead-Free
Solder composition 
code (Refer to the 
table at the right.)
<Solder composition code of lead-free solder> 
Solder composition
Sn-Ag-Cu
Sn-Ag-Bi
Sn-Ag-Bi-Cu
Sn-Zn-Bi
Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
Bi-Sn-Ag-P
Bi-Sn-Ag
a
b
z
i
n
s
p
Solder composition code
a
– 1 –
1. PORT CONNECTIONS
2. INSTALLING THE INTEGRATED
REAR DISPLAY (UP-I20DP)
1)  Remove the two screws. Disengage the four pawls and remove the
rear cover unit.
Clamping: 5.0±0.2kgf.cm
2) Replace the UP-I20DP Sheet metal with a new one.
It attaches using the removed screw A .
Units produced prior to Feb. 2004 will require replacement of
support angle.
3) Remove sheet 1  from the rear filter, and remove Rear cover Sheet
2
 and install the UP-I20DP 5  and secure with two screws 3 , 4 .
4) Wrap the UP-I20DP harness one turn around the rib 1 ,
insert the connector 2  and install the rear cover unit. 
From  2004  February  production,  the  sheet  metal  for  the  UP-X500  is
included in the package.
Ref. No. Symbol
Description
1
RS232 COM - 1
2
RS232 COM - 2
3
RS232 COM - 3
4
RS232 COM - 4
5
UP-P20DP/DPB Remote Pole display connection
6
UP-I20DP Integrated display connection
7
Ethernet LAN connector
8
Cash Drawer connectors 1  and 2
1
2
3
4
5
6
7
8
1
2
3
4
3
2
1
3
2
1
1
2
DRAWER
1
2
3
4
3
2
1
3
2
1
1
2
DRAWER
A
A
1
3
3
5
4
2
*
This screw is packed
together with the UP-I20DP.
1
2
DC jack
When removing the DC plug 
from the DC jack, be sure to 
release the lock and use a 
great care not to touch the 
peripheral ribs with your 
fingers.
*
– 2 –
3. INSTALLING THE REMOTE POLE 
DISPLAY (UP-P20DP/DPB)
1) Remove the connector sheet A .
2) Attach the UP-P20DP cable 1 .
*
 How to Extend Display Pole
The pole can be extended by installing the attached pole to the stan-
dard pole.
COMPONENT LIST:
1) Remove the five screws 1 .
2) Remove the Base angle 2 .
3) Remove the PWB unit 3  from the Base cabinet 4 .
4) Remove the display cable 5  from the PWB unit 3 .
5) Remove the two screws 6 .
6) Remove the Base cabinet 4  from the pole cabinet 7 .
No.
NAME
USE
Q’ty
7
, G
Pole cabinet
Pole extension
2
H
Screw (M3
×
4)
Pole connection
4
I
Screw (M4
×
16)
Securing the UP-P20DP to the
wooden table
4
J
Screw (M4
×
20)
Securing the UP-P20DP to the
metal table
4
K
Nut
Securing the UP-P20DP to the
metal table
4
L
Display cable (S)
This display cable (S) should be 
used instead of the standard 
cable and earth wire if the UP-
20DP’s standard pole is 
removed to lower the height of 
the UP-20DP.
1
M
Earth wire (S)
1
1
A
Pattern side(PWB)
Core
1
2
3
4
5
1
6
4
7
The standard position of a core and the clamp.
100m
Page of 10
Display

Download Sharp UP-3515 (serv.man8) User Guide / Operation Manual

Here you can read online and download Sharp UP-3515 (serv.man8) User Guide / Operation Manual in PDF. UP-3515 (serv.man8) user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp UP-3515 (serv.man8) EPOS. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.