Read Sharp UP-3500 (serv.man21) Service Manual online
Page 9 14
6.
Improvement of the SCM(+) / SCM() function.
With the existing SRV parameter #907A, SCM input can be set to compulsory.
In case this parameter is set i.e. to 6 (compulsory for all Clerks) one Clerk has to make the SCM
input in order to perform the SCM entry for all Clerks.
In previous versions, in case of SCM(2), the ECR is comparing the SCM(2) amount against the
individual Clerk totalizer of that Clerk who wants to make the SCM(2). If the Clerk who wants to
make the SCM(2) differs from that Clerk who makes the SCM(+), it is possible to make a SCM(2) of
only that amount which is less or equal to the turnover of the Clerk. In this case, the previous
entered SCM(+) amount by the other Clerk is disregarded. This has been changed at this version.
If SRV parameter #907A is set to +1 (1 or 5), the ECR compares the SCM(2) amount against the
individual Clerk totalizer. This is like in the previous version.
If SRV parameter #907A is set to +2 (2 or 6), the ECR compares the SCM(2) amount against the
CA/CHK ID totalizer of the terminal. This has been changed compared to the previous version.
If SRV parameter #907A is set to 0 or 4 (SCM input is not compulsory), the new below SRV
parameter #991A will be considered.
If SRV parameter #991A is set to +4, the ECR compares the SCM(2) amount against the CA/CHK ID
totalizer.
If SRV parameter #991A is set to 0, the ECR compares the SCM(2) amount against the individual
Clerk totalizer.
Because of the additional checking of the new SRV parameter, it is possible to set up the ECR like
with the previous ROM version.
In case this parameter is set i.e. to 6 (compulsory for all Clerks) one Clerk has to make the SCM
input in order to perform the SCM entry for all Clerks.
In previous versions, in case of SCM(2), the ECR is comparing the SCM(2) amount against the
individual Clerk totalizer of that Clerk who wants to make the SCM(2). If the Clerk who wants to
make the SCM(2) differs from that Clerk who makes the SCM(+), it is possible to make a SCM(2) of
only that amount which is less or equal to the turnover of the Clerk. In this case, the previous
entered SCM(+) amount by the other Clerk is disregarded. This has been changed at this version.
If SRV parameter #907A is set to +1 (1 or 5), the ECR compares the SCM(2) amount against the
individual Clerk totalizer. This is like in the previous version.
If SRV parameter #907A is set to +2 (2 or 6), the ECR compares the SCM(2) amount against the
CA/CHK ID totalizer of the terminal. This has been changed compared to the previous version.
If SRV parameter #907A is set to 0 or 4 (SCM input is not compulsory), the new below SRV
parameter #991A will be considered.
If SRV parameter #991A is set to +4, the ECR compares the SCM(2) amount against the CA/CHK ID
totalizer.
If SRV parameter #991A is set to 0, the ECR compares the SCM(2) amount against the individual
Clerk totalizer.
Because of the additional checking of the new SRV parameter, it is possible to set up the ECR like
with the previous ROM version.
Checking of SCM(2) amount
(only if 907A=0 or 4)
GLU key status
after Media & Bill
9912A Default
Setting 1
0
√
Setting 2
1
against individual Clerk
totalizer
Setting 3
2
Setting 1
4
Setting 2
5
against
CA/CHK ID totalizer
Setting 3
6
Entry of SCM after registration
SCM compulsory
9072A Default
non compulsory (refer #991A)
0
√
for individual Clerk (Cashier)
1
disable
for all Clerks (Cashiers)
2
non compulsory (refer #991A)
4
for individual Clerk (Cashier)
5
enable
for all Clerks (Cashiers)
6
Click on the first or last page to see other UP-3500 (serv.man21) service manuals if exist.