Read Sharp ER-A570 (serv.man5) Service Manual online
No.
Job#
M/S
Item
Key sequence
7
#925 MRS = 0000
M/S
925-D: 1. PLU stock control system
2. Resetting in the open store state.
<<Detailed descriptions of the parameter for Job #925>>
925-A
925-A
1
Method of daily general resetting of the entire system at the master:
It is specified whether only those data that has individually been reset or that data and the
current sales data should be reset when resetting of the entire system is take.
Note here that if the machine is programmed to disable individual resetting (by B of
SRV-mode programming Job #925), not only individual resetting but also resetting of the
entire system cannot be achieved unless "Those data that has individually been reset and
the current sales data are reset together" has been selected.
It is specified whether only those data that has individually been reset or that data and the
current sales data should be reset when resetting of the entire system is take.
Note here that if the machine is programmed to disable individual resetting (by B of
SRV-mode programming Job #925), not only individual resetting but also resetting of the
entire system cannot be achieved unless "Those data that has individually been reset and
the current sales data are reset together" has been selected.
2
Automatic clearing of the individual resetting memory at the time of consolidation daily
total general resetting No/Yes
The machine can be programmed to clear the individual resetting memory when general
Z1 resetting of the entire system is taken. If the memory is not cleared data is
accumulated each time individual resetting is taken until job #99 is executed.
total general resetting No/Yes
The machine can be programmed to clear the individual resetting memory when general
Z1 resetting of the entire system is taken. If the memory is not cleared data is
accumulated each time individual resetting is taken until job #99 is executed.
3
Execution of Job #99 when consolidation daily total general resetting has not been taken
Enable/Disable:
Job #99 can be executed even if general Z1 resetting of the entire system is not taken.
Enable/Disable:
Job #99 can be executed even if general Z1 resetting of the entire system is not taken.
925-B
4
Any entry operation is inhibited until Job #99 is executed after consolidation or individual
daily total general resetting has been taken No/Yes:
This parameter enables the master to restrict the resetting job at satellites.
daily total general resetting has been taken No/Yes:
This parameter enables the master to restrict the resetting job at satellites.
5
Individual resetting Enable/Disable:
The master alone can be made capable of resetting by selecting "Disable".
When selecting "Enable", or "Disable", however, the selection of the resetting method
mentioned
The master alone can be made capable of resetting by selecting "Disable".
When selecting "Enable", or "Disable", however, the selection of the resetting method
mentioned
1
above should well be noted.
925-C
6
Type of printing of daily total and periodic total general X/Z reports:
The following three types are available:
a) Printing of only X/Z reports on individual machines
b) Printing of a consolidation X/Z report only
c) Printing of X/Z reports on individual machines, followed by the printing of a
The following three types are available:
a) Printing of only X/Z reports on individual machines
b) Printing of a consolidation X/Z report only
c) Printing of X/Z reports on individual machines, followed by the printing of a
consolidation X/Z report
Note: This programming
1
-
4
is valid for the system that has the save file.
Reading of SRV-mode program data
925-D
7
PLU stock control in the inline system
a) Stock control in inline system is available in two types: individual and centralized
a) Stock control in inline system is available in two types: individual and centralized
systems.
b) Centralized stock control system
Program data only stock is only stored in the master.
Stock data in each satellite must be zero before a stock entry is made.
When a consolidaton report is taken, stock data in respective satellites are
consolidated and is add to stock data in the master.
Then the sum is printed.
Stock data in each satellite is reset to zero at this time.
Stock data in each satellite must be zero before a stock entry is made.
When a consolidaton report is taken, stock data in respective satellites are
consolidated and is add to stock data in the master.
Then the sum is printed.
Stock data in each satellite is reset to zero at this time.
Notice) In this system, stock counter in each satellite is always negative.
So, Entry which makes the PLU stock counter negative must be Allowed
unconditionally. (SRV. JOB#906-A)
unconditionally. (SRV. JOB#906-A)
c) Individual control system
Program data on stock is stored in the master and stellites, respectively.
When a consolidation report is taken, stock data in the master and satellites is
consolidated and printed.
The consolidation does not affect the stock data in the master.
When a consolidation report is taken, stock data in the master and satellites is
consolidated and printed.
The consolidation does not affect the stock data in the master.
1. PLU stock
control
system
system
2. Resetting in
the open
store state
store state
925-D
Centralized
Disable
0
Enable
1
Individual
Disable
2
Enable
3
1 11
Click on the first or last page to see other ER-A570 (serv.man5) service manuals if exist.