Read Sharp ER-A450S (serv.man9) FAQ online
(Scanner Questions)
How are the RS232 channels set up .
There are 2 Channels on the ERA450S these are Channel Number 1 for
standard port 2 and Channel number 8 for standard port 1 (see page 1-4
hardware manual)
When connecting a Scanner to the machine you should use channel 8, this is
the connector nearest the front of the machine (hardware manual page 1-4)
standard port 2 and Channel number 8 for standard port 1 (see page 1-4
hardware manual)
When connecting a Scanner to the machine you should use channel 8, this is
the connector nearest the front of the machine (hardware manual page 1-4)
What programming is required to set up the ERA450S for bar code scanning.
It is recommended that the scanner is connected to Channel 8 (this is the port
nearest the front of the machine)
nearest the front of the machine)
Job Code 2690 . x 2 x 8000 ST TL
Job Code 2691 can be changed if required (depending on scanner
configuration) but should be remain as default if possible.
Job Code 2691 can be changed if required (depending on scanner
configuration) but should be remain as default if possible.
Can a scanner be powered directly by the ERA450.
Yes, for example the ERA6HS1 can be used. There is a jumper switch
position that need to be set (this is the jumper next to channel 8) this supplies
+5v to pin 9, which will supply 5v to the scanner.
position that need to be set (this is the jumper next to channel 8) this supplies
+5v to pin 9, which will supply 5v to the scanner.
What type of scanners can be connected to the ERA450S
The scanner protocol is the same as that of the ERA610 so any scanners that
can be connected to that can be used, The scanners we have tested are the
scanners we supply they are the ER6HS1 and the LH80ERCCD74.
can be connected to that can be used, The scanners we have tested are the
scanners we supply they are the ER6HS1 and the LH80ERCCD74.
How does the Price Inquiry feature work
Press Price Inquiry key scan item, price will appear press AMT key to confirm
selling price or CL to cancel inquiring, alternatively at this stage you can enter
into MGR mode and temporarily override the price.
selling price or CL to cancel inquiring, alternatively at this stage you can enter
into MGR mode and temporarily override the price.
When an item is scanned a broken line appears on the display.
This is because the ERA450S has gone into learning mode (The item has not
yet been programmed into the machine) you can enter the price and
associated department and this will be stored into the memory.
yet been programmed into the machine) you can enter the price and
associated department and this will be stored into the memory.
What programming is required to set up Communications to a PC
Job Code 2690 . x 1 x 1000 TL sets up the channel
Job Code 6110 . x 1 TL sets up terminal number 1
Job Code 6112 . x 6 TL sets up the Baud Rate for 19200.
Job Code 6110 . x 1 TL sets up terminal number 1
Job Code 6112 . x 6 TL sets up the Baud Rate for 19200.
What is the maximum number of EANs on the ERA450S
With standard machine there is room for 5200 EANs (12 text characters) with
the ER03RA RAM upgrade you can have approximately 17,992.
the ER03RA RAM upgrade you can have approximately 17,992.
How do I take a complete RAM back up to another machine.
Using job codes 996 & 998 Ram data can be transferred through the RS232
Port (nearest the front of the machine) using a cable with the following spec:-
Port (nearest the front of the machine) using a cable with the following spec:-
2---------3
3---------2
7---------1
1---------7
4---------6
8
6---------4
8
5---------5
3---------2
7---------1
1---------7
4---------6
8
6---------4
8
5---------5
What is the Memory (Ram) size on the ERA450S
The Standard Memory is 256K the option Ram (ER-03RA) is 512K taking the
maximum memory to 768K
maximum memory to 768K
Does the ERA450S have a Training Clerk feature
Yes one Clerk can be set at job code 948#
Yes Job code 989 . x TL in SRV Mode will do this.
Is there a full list of Error codes for the ERA450S
Yes for the complete list please refer to the service manual page 7-1, there is
also a listing in the Operators manual on page 158)
also a listing in the Operators manual on page 158)
Can the ERA450S program be downloaded to the ER02FD.
Yes (01FD functions only please refer to page 6-3 hardware manual for dip
switch settings for the 02FD unit.)
switch settings for the 02FD unit.)
