DV-NC60H (serv.man8). Operation of pickup - Sharp DVD Service Manual (repair manual)

dv-nc60h (serv.man8) service manual
Model
DV-NC60H (serv.man8)
Pages
1 Few pages! See other manuals at the bottom of the first or last page.
Size
68.48 KB
Type
PDF
Document
Service Manual
Brand
Device
DVD / Operation of pickup
File
dv-nc60h-sm8.pdf
Date

Read Sharp DV-NC60H (serv.man8) Service Manual online

14
DV-NC55S/H
DV-NC60H
7. OPERATION OF PICKUP
7-1. CIRCUIT CONFIGURATION OF PICKUP
The pickup unit reads signals from the disk, and the flexible cable is connected to the board. The following signals flow through the
cable.
7-2. EQUIVALENT CIRCUIT OF PICKUP
7-3. POLARITIES OF SIGNAL
Focus
When electric current is flowed
FO+, FO-
from FO+ to FO-, the lens comes
 to near the disk.
Tracking
When electric current is flowed
TR+, TR-
from TR+ to TR-, the lens goes
toward the outer circumference.
FO+
TR–
TR+
FO–
ACTUATOR
OSC
V
OS

+

+

+

+
HOLOGRAM LASER UNIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
TR–
FO+
TR+
FO–
VR
PD
V
CC
GND
LD
GND
V
OS
NC
NC
V
ref
(VCC/2)
VA
VD
NC
GND
VB
VC
(NC)
Power adjust
HIGH-FREQUENCY CONVOLUTION
LD
PD
VA
VB
VC
VD
V
ref
V
cc
GND
7-4. SIGNALS OF PICKUP
7-4-1. Tracking drive signal (TR+, TR-)
The signal drives the tracking servo mechanism which projects the beam on the track by moving the objective lens (OL) to the outer
or inner circumference (at a right angle against the track) of the disk.
7-4-2. Focus drive signal (FO+, FO-)
The signal drives the focus servo mechanism which aligns the focus on the pit of the disk
by elevating OL (vertically against the disk surface.)
The VR terminal is connected to GND.
2-focus objective lens
Actuator assembly
7-4-3. Monitor Diode (PD)
Since the laser diode largely varies output of the laser light even if the flowing current is slightly varied, the projection
light is detected with the monitor diode to control the laser light to be equally output.
Since the current varies on the monitor diode according to the intensity of the received light of the laser diode, the drive current of
the laser diode is reduced if the current of the monitor diode increases. On the contrary, the drive current of the laser diode is increased
if the current of the monitor diode decreases.
As the projection light of the laser diode becomes stronger, the current of the monitor diode increases to increase the current which
flows into the monitor diode output (PD).  This is input to the pin 44 of IC301 and is compared with the reference voltage to control
the drive current of the laser diode.
The circuit is called ALPC (Automatic Laser Power Control).
7-4-4. Laser diode drive current control (LD)
Power supply to drive the laser diode
7-4-5. High-frequency convolution module power supply (VOSC)
The high-frequency convolution imposes the high-frequency signal on the DC current to impose the high frequency on the drive
current of the laser. Thus, the interference of outgoing light and reflected light is prevented.
LD
PD
7-4-6. HF Signal (VA, VB, VC, VD)
Signals recorded in the disk
When the quantity of laser light increases, the
current shown in figure increases and the PD
terminal voltage rises.
IC301 is used to control. The LD terminal voltage
lowers, and the quantity of light reduces. (IC301 is
actuated by voltage input.)
Display

Download Sharp DV-NC60H (serv.man8) Service Manual (Repair Manual)

Here you can read online and download Sharp DV-NC60H (serv.man8) Service Manual in PDF. DV-NC60H (serv.man8) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp DV-NC60H (serv.man8) DVD. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.