BD-HP35S (serv.man3). Removing Of MajorParts - Sharp DVD Service Manual (repair manual)

bd-hp35s (serv.man3) service manual
Model
BD-HP35S (serv.man3)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
424.26 KB
Type
PDF
Document
Service Manual
Brand
Device
DVD / Blu-Ray Player / Removing Of MajorParts
File
bd-hp35s-sm3.pdf
Date

Read Sharp BD-HP35S (serv.man3) Service Manual online

BD-HP35S
3 – 1
BDHP35S
Service Manual
 
CHAPTER 3. 
REMOVING OF MAJOR
PARTS
[1] REMOVING OF MAJOR PARTS
1. Removing the Top Cabinet and Front Panel Ass’y
1. Remove the 3 lock screws 
, 2 lock screws 
 and detach the Top
Cabinet.
2. Unhook claws of the Front Panel and detach the Front Panel Ass’y.
2. Removing the Rear Panel
1. Remove the 2 lock screws  , 1 lock screw  , 2 lock screws 
and detach the Rear Panel.
3. Removing the BD DRIVE Unit
1. Disconnect the 2 FFC Connectors.
2. Remove the 4 lock screws 
 and detach the BD DRIVE Unit.
3. Detach the Tray Blind Cover.
4. Removing the LCD Unit, MAIN Unit and POWER
Unit
1. Disconnect the FFC (LCD - MAIN).
2. Disconnect the Connecting Cord (USB - MAIN).
3. Remove the 2 lock screws 
 and detach the LCD Unit.
4. Disconnect the Connecting Cord (POWER - MAIN).
5. Remove the 2 lock screws 
 and detach the MAIN Unit.
6. Remove the 4 lock screws 
 and detach the POWER Unit.
Top Cabinet
Front Panel Ass'y
1
2
2
Rear Panel
4
3
3
5
BD DRIVE Unit
FFC Connector
Tray Blind Cover
6
POWER Unit
FFC
(LCD - MAIN)
Connecting Cord
(POWER - MAIN)
Connecting Cord
(USB - MAIN)
MAIN Unit
LCD Unit
a
a
b
c
b
c
d
d
8
7
9
BD-HP35S
3 – 2
[2] IMPORTANT SERVICE NOTICE
1. When replacing the main PWB, update its software using a CD or USB memory.
3. The IC7801-4 (DDR) are of BGA (Ball Grid Array) type and can only be replaced using a specific device.
 
[3] UPGRADING THE VERSION
1. Procedure with a CD
1. Write the updated software on a CD to prepare the version-upgrading CD.
2. Connect the set to the monitor with an HDMI cable. (Keep the HDMI cable connected until the version-upgrading has been completed.)
3. Using the “POWER” key (on the set itself or on the remote controller), turn on the power.
* Do not turn on the power with the “EJECT” key.
4. Press the “EJECT” key to open the tray. Place the upgrading CD on the tray and press the “EJECT” key again to close the tray.
5. The CD is opened and the power turns off itself.
6. The power turns on itself and the upgrading gets started.
LCD display: V-UP blinking  
→ V-UP kept on
Mode display: Blue LED blinking  
→ Blue LED kept on
Monitor screen: Upgrading progress displayed
8. Take the CD out of the tray and press the “POWER” key to turn on the power again.
9. When the wallpaper shows up, hold down the “POWER” key to do the resetting. (Keep the “POWER” key depressed until the RESET message
appears on the LCD. (About 10 seconds))
10.Press the “POWER” key again to turn on the power.
11.When the wallpaper shows up again, move from [Settings] to [Version] to make sure the software is upgraded.
12.When the upgrading has been successfully made, close the [Version] confirm screen and turn off the power. If it has failed, take the procedure
over again from Step 3 above.
2. Procedure with a USB memory
1. Write the updated software on a USB memory to prepare the version-upgrading USB memory.
2. Connect the set to the monitor with an HDMI cable. (Keep the HDMI cable connected until the version-upgrading has been completed.)
3. Using the “POWER” key (on the set itself or on the remote controller), turn on the power.
* Do not turn on the power with the “EJECT” key.
4. Insert the upgrading USB memory into the USB port.
5. When the USB memory has been recognized (the “x” mark on the USB icon disappears and the USB recognition on-screen display appears),
move from [Settings], [Software Update Settings], [Manual Update] to [USB Memory], and then press the “ENTER” or “
” key.
6. Press “OK” on the USB recognition confirm screen.
7. The power turns on itself and the upgrading gets started.
LCD display: V-UP blinking  
→ V-UP kept on
Mode display: Blue LED blinking  
→ Blue LED kept on
Monitor screen: Upgrading progress displayed
9. Draw the USB memory out of the USB port and press the “POWER” key to turn on the power again.
10.When the wallpaper shows up, hold down the “POWER” key to do the resetting. (Keep the “POWER” key depressed until the RESET message
appears on the LCD. (About 10 seconds))
11.Press the “POWER” key again to turn on the power.
12.When the wallpaper shows up again, move from [Settings] to [Version] to make sure the software is upgraded.
13.When the upgrading has been successfully made, close the [Version] confirm screen and turn off the power. If it has failed, take the procedure
over again from Step 3 above.
Consult with your Services Company as we cannot provide the upgrading software.
Page of 2
Display

Download Sharp BD-HP35S (serv.man3) Service Manual (Repair Manual)

Here you can read online and download Sharp BD-HP35S (serv.man3) Service Manual in PDF. BD-HP35S (serv.man3) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp BD-HP35S (serv.man3) Blu-Ray Player. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.