XL-HP434 (serv.man3). Adjustments - Sharp Audio Service Manual (repair manual)

xl-hp434 (serv.man3) service manual
Model
XL-HP434 (serv.man3)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
59.02 KB
Type
PDF
Document
Service Manual
Brand
Device
Audio / System / Adjustments
File
xl-hp434-sm3.pdf
Date

Read Sharp XL-HP434 (serv.man3) Service Manual online

XL-HP434H
2 – 1
Audio
XL-HP434H
Service Manual
XLHP434H
Market
E
 
CHAPTER 2. 
ADJUSTMENTS
[1] ADJUSTMENT
1. MECHANISM SECTION
 Driving Force Check
 Torque Check
2. TUNER SECTION
fL: Low-range frequency
fH: High-range frequency
 AM IF/RF
Signal generator: 400 Hz, 30%, AM modulated
Notes:
1. Description of the "FM IF Adjustment" is not carried on this Manual.
It is because the IF coil in the FM front end section has been best
adjusted in the factory so that its further adjustment is not needed
at the field. When replacing the FM front end assembly, no adjust-
ment is needed either.
2. The parts in the FM front end section are prepared in a complete
unit, so you can't obtain each part individually.
 Tape Speed
3. CD SECTION
Adjustment
Since this CD system incorporates the following automatic adjust-
ment functions, readjustment is not needed when replacing the
pickup. Therefore, different PWBs and pickups can be combined
freely.
Each time a disc is changed, these adjustments are performed
automatically. Therefore, playback of each disc can be performed
under optimum conditions.
Items adjusted automatically
1) Offset adjustment (The offset voltage between the head amplifier
output and the VREF reference voltage is compensated  inside  the
IC.)
*
Focus offset adjustment
*
Tracking offset adjustment
2) Tracking balance adjustment
3) Gain adjustment (The gain is compensated inside the IC so that the
loop gain at the gain crossover frequency will be 0 dB.)
*
Focus gain adjustment
*
Tracking gain adjustment
4. CD ERROR CODE DESCRIPTION
*
'CHECKING'
If Error is detected, 'CHECKING' will be displayed instead of 'ER-
CD**'. 'ER-CD**' display will only be displayed when error had been
detected for the 5th times.
Torque Meter
Specified Value
Play: TW-2111
Over 80 g
Torque Meter
Specified Value
Play: TW-2111
30 to 80 g.cm
Fast forward: TW-2231
70 to 180 g.cm
Rewind: TW-2231
70 to 180 g.cm
Test Stage
Frequency
Frequency
Display
Setting/
Adjusting
Parts
Instrument
Connection
AM IF
450 kHz
1,620 kHz
T351
*1
AM Band 
Coverage
522 kHz
(fL): T306
1.1 ± 0.1 V
*2
AM Tracking
990 kHz
990 kHz
(fL): T303
*1
*1. Input: Antenna
Output: TP302
*2. Input: Antenna
Output: TP301
Figure 2 ADJUSTMENT POINTS
AM
LOOP
ANTENNA
IC302
T351
IC303
L354
T303
T306
CNP302
SO301
FE301
TP302
TP301
AM TRACKING fL
AM BAND
COVERAGE fL
AM IF
ANTENNA
TERMINAL
TUNER PWB-C
20
R357
R356
C393
Test Tape
Adjusting 
Point
Specified 
Value
Instrument 
Connection
Normal 
speed
MTT-111
Variable 
Resistor in 
motor.
3,000 ± 30 Hz
Speaker Ter-
minal (Load 
resistance: 6 
ohms)
Figure 1
Error
Explanation
01
When Pickup set inner position, inner switch cannot detect 
'ON' level for 10 secs.
10*
CAM error. Can't detect CAM switch when CAM is moving. 
11*
When it detect cam operation error during initialize process.
20*
TRAY error. Can't detect TRAY switch when TRAY is mov-
ing.
21*
When it detect TRAY operation error during initialize pro-
cess.
31
When it change to CD function, DSP cannot read initial data.
TAPE MECHANISM
Tape
Motor
Variable Resistor in motor
XL-HP434H
2 – 2
[2] TEST MODE
 Setting the test mode
During stand-by mode, press ON/STAND-BY button while pressing
down the 
button and X-BASS/DEMO button. then, press the CD
button to enter the test mode.
IL isn’t done
OPEN/CLOSE operation is using manual.
IL isn’t done
<<
>>,<<
>>buttons make pick's slide possible.
IL isn’t done
to page 2-3
<<PLAY>> key input.
C D
T E S T
A
Do TOC IL. Do normal play.
When these following key is input into PLAY key, track num-
ber can be appoint directly.
<<MEMORY>>
key input.
<<
1>> key: Track 4
<<
2>> key: Track 9
<<
3>> key: Track 15
Adjustment result automatically will
display as below for each 2 sec:
a) "FOF_XXXX"
b) "TOF_XXXX"
c) "TBAL_XX"
d) "TGAN_XX"
f) "FGAN_XX"
g) "RFLS_XX"
––––––––
<<STOP>> key input.
STOP
explanation:
a) Focus off set
= "FOF_XXXX"
b)Tracking off set
= "TOF_XXXX"
c)Tracking balance
= "TBAL_XX"
d)Tracking Gain
= "TGAN_XX"
f) Focus Gain
= "FGAN_XX"
g) RF level shift
= "RFLS_XX"
VOL — Last memory
P.GEQ — FLAT
X-BASS — OFF
To cancel : Power OFF
XL-HP434H
2 – 3
Sliding the PICKUP with<<
>>, <<
>> button must only be
in STOP mode.
<<MEMORY>> key input.
Laser ON.
<<MEMORY>> key input.
Tracking OFF play at that specific point.
<<MEMORY>> key input.
Tracking ON play from that specific point.
<<MEMORY>> key input.
Adjustment result automatically will display as below for each 2 sec :
a) "FOF_XXXX"
b) "TOF_XXXX"
c) "TBAL_XX"
d) "TGAN_XX"
f) "FGAN_XX"
g) "RFLS_XX"
<<STOP>> key input.
STOP
explanation:
a) Focus off set
= "FOF_XXXX"
b)Tracking off set
= "TOF_XXXX"
c)Tracking balance
= "TBAL_XX"
d)Tracking Gain
= "TGAN_XX"
f) Focus Gain
= "FGAN_XX"
g) RF level shift
= "RFLS_XX"
VOL — Last memory
P.GEQ — FLAT
X-BASS — OFF
To cancel : Power OFF
A
XL-HP434H
2 – 4
[3] Standard Specification of Stereo System Error Message Display Contents
(*) CHECKING:
If CD changer mechanism error is detected, 'CHECKING' will be display instead of 'ER-CD**'. 'ER-CD**' display will only be display when error had
been detected for the 5 th times.
Speaker abnormal detection and +B PROTECTION display
In case speaker abnormal detection or +B PROTECTION had occurred, it can be check by pressing 'POWER', '
' and 'X-BASS' button. Micro-
Computer version number will displayed as "um******".
Press ‘VIDEO/AUX’ button during version number display and then press ‘POWER’, ‘MEMORY/SET’ and ‘VIDEO/AUX’ button. Display will show "S**
B**". S is referring to speaker abnormal detection and B is referring to +B PROTECTION. ** is in hex valve.
+B PROTECTION is condition when irregular process occur on power supply line.
BEFORE TRANSPORTING THE UNIT
The following process need to be taken after set tapering/parts replacement.
1. Press the ON/STAND-BY button to enter stand-by mode.
2. While pressing down the 
button and the X-BASS/DEMO button, press the ON/STAND-BY button. The Micro Computer version number will
be displayed as "um******".
3. Press OPEN/CLOSE button until "WAIT"--> "FINISHED" appears.
4. Unplug the AC cord and the unit is ready for transporting.
Error Contents
DISPLAY
Notes
CD
Pickup Mechanism Error.
'ER-CD01'
PU-IN SW Detection NG.
CD Changer Mechanism Error.
'ER-CD**' (*)
10: CAM SW Detection NG during normal operation
11: CAM SW Detection NG during initialize process
20:TRAY SW Detection NG during normal operation
21:TRAY SW Detection NG during initialize process
CD DSP Communication Error.
'ER-CD31'
DSP COMMUNICATION ERROR.
Focus Not Match/IL Time Over.
'NO DISC'
TUNER
PLL Unlock.
FM
MHz
PLL Unlock.
87.50
Page of 4
Display

Download Sharp XL-HP434 (serv.man3) Service Manual (Repair Manual)

Here you can read online and download Sharp XL-HP434 (serv.man3) Service Manual in PDF. XL-HP434 (serv.man3) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp XL-HP434 (serv.man3) System. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.