Read Sharp XL-60 (serv.man11) Service Manual online
– 11 –
XL-60H/70H
Figure 11-4
How to remove the pickup (See Fig. 11-4)
1. Remove the mechanism cover, paying attention to the
pawls (A1) x 4 pcs.
2. Remove the screws (A2) x 2 pcs., to remove the shaft (A3)
x 1 pc.
3. Remove the stop washer (A4) x 1 pc., to remove the gear
(A5) x 1 pc.
4. Remove the pickup.
CD MECHANISM SECTION
Perform steps 1, 2 and 10 to 12 of the disassembly method to
remove the CD mechanism.
remove the CD mechanism.
Pickup Unit
(A2) x2
ø2.6 x6mm
ø2.6 x6mm
(A1) x2
CD Mechanism
Shaft
(A3) x1
(A3) x1
Gear
(A5) x1
(A5) x1
StopWasher
(A4) x1
(A4) x1
Mechanism Cover
(A1) x2
How to remove the tape mechanism PWB
(See Fig. 11-1.)
(See Fig. 11-1.)
1. Remove the screws (F1) x 1 pc., to remove the tape
mechanism PWB.
2. Remove the screws (F2) x 1 pc.
3. Remove the solder joints (F3) x 2 pcs., to remove the tape
3. Remove the solder joints (F3) x 2 pcs., to remove the tape
mechanism PWB.
How to remove the jog motor
(See Figs. 11-2.)
(See Figs. 11-2.)
1. Remove the side panel and top cabinet.
2. Remove the jog belt (G1) x 1 pc., from the motor pulley.
3. Remove the screws (G2) x 2 pcs., to remove the jog motor.
Note:
When putting on the belt, ascertain that the belt is not twisted,
and clean it.
2. Remove the jog belt (G1) x 1 pc., from the motor pulley.
3. Remove the screws (G2) x 2 pcs., to remove the jog motor.
Note:
When putting on the belt, ascertain that the belt is not twisted,
and clean it.
Figure 11-1
Figure 11-2
(G2)x2
ø2x5mm
ø2x5mm
Worm
Gear
Gear
Jog Belt
(G1)x1
(G1)x1
Jog Motor
Holder
Holder
Jog Motor
Display PWB
Tape
Mechanism
PWB
Mechanism
PWB
Tape
Mechanism
PWB
Mechanism
PWB
(F3)x2
Solder
Joint
Solder
Joint
(F2)x1
ø2x8mm
ø2x8mm
(F1)x1
ø2x3mm
ø2x3mm
How to remove the CD lid motor
(See Figs. 11-3.)
(See Figs. 11-3.)
1. Remove the CD PWB.
2. Remove the belt (H1) x 1 pc., from the motor pulley.
3. Remove the screws (H2) x 2 pcs., to remove the CD Lid
2. Remove the belt (H1) x 1 pc., from the motor pulley.
3. Remove the screws (H2) x 2 pcs., to remove the CD Lid
motor.
Note:
When putting on the belt, ascertain that the belt is not twisted,
and clean it.
When putting on the belt, ascertain that the belt is not twisted,
and clean it.
(H2)x2
ø2.5x10mm
CD Lid
Motor
Motor
(H1)x1
Belt
Worm
Gear
Gear
Figure 11-3
Note:
After removing the connector for the optical pickup from the
connector, wrap the conductive aluminium foil around the
front end of connector remove to protect the optical pickup
from electrostatic damage.
After removing the connector for the optical pickup from the
connector, wrap the conductive aluminium foil around the
front end of connector remove to protect the optical pickup
from electrostatic damage.
Display