Read Sharp XL-505E (serv.man5) Service Manual online
– 3 –
XL-505H,505E,507E/CP-505,505E,507
Cassette deck section
Frequency response:
50 - 14,000 Hz (Normal tape)
Signal/noise ratio:
55 dB
(XL-505H/505E)
Signal/noise ratio:
Signal/noise ratio:
50 dB
(XL-507E)
Wow and flutter:
Wow and flutter:
0.3 % (DIN 45 511)
(XL-505H/505E)
Wow and flutter:
Wow and flutter:
0.25 % (WRMS)
(XL-507E)
Type:
Full range speaker system
Speakers:
10 cm (4") full-range speaker
Rated input power:
5 W
Maximum input power: 10 W
Impedance:
Impedance:
4 ohms
Dimensions:
Width; 145 mm (5-3/4")
(CP-505/507)
Height; 240 mm (9-1/2")
Depth; 183 mm (7-1/4")
Depth; 183 mm (7-1/4")
Dimensions:
Width; 145 mm (5-3/4")
(CP-505E)
Height; 240 mm (9-1/2")
Depth; 133 mm (5-1/4")
Depth; 133 mm (5-1/4")
Weight:
1.1 kg (2.4 lbs.)/each
(CP-505/507)
Weight:
Weight:
1.0 kg (2.2 lbs.)/each
(CP-505E)
General
Power source:
AC 230 V, 50 Hz
Power consumption:
52 W
Dimensions:
Width; 160 mm (6-5/16")
Height; 240 mm (9-1/2")
Depth; 250 mm (9-7/8")
Height; 240 mm (9-1/2")
Depth; 250 mm (9-7/8")
Weight:
2.6 kg (5.7 lbs.)
Amplifier section
Output power:
PMPO; 28 W (total)
(XL-505H/505E)
MPO; 14 W (7 W + 7 W) (DIN 45 324)
RMS; 10 W (5 W + 5 W) (DIN 45 324)
RMS; 10 W (5 W + 5 W) (DIN 45 324)
Output power:
MPO; 14 W (7 W + 7 W) (10 % T.H.D.)
(XL-507E)
RMS; 10 W (5 W + 5 W) (10 % T.H.D.)
Output terminals:
Speakers; 4 ohms
Headphones; 16-50 ohms
(recommended; 32 ohms)
Headphones; 16-50 ohms
(recommended; 32 ohms)
Tuner section
Frequency range:
FM; 87.5 - 108 MHz
AM; 522 - 1,620 kHz
AM; 522 - 1,620 kHz
Compact disc player section
Type:
Compact disc player
Signal readout:
Non-contact, 3-beam semi-conductor
laser pickup
laser pickup
D/A Converter:
1-bit D/A converter
Filter:
8-times oversampling digital filter
Frequency response:
20 - 20,000 Hz
Wow and flutter:
Unmeasurable
(less than 0.001% W.peak)
(less than 0.001% W.peak)
SPECIFICATIONS
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
TO THE OPERATION MANUAL.
Before returning the unit to the customer after completion of a
repair or adjustment it is necessary for the following withstand
voltage test to be applied to ensure the unit is safe for the
customer to use.
Setting of Withstanding Voltage Tester and set.
repair or adjustment it is necessary for the following withstand
voltage test to be applied to ensure the unit is safe for the
customer to use.
Setting of Withstanding Voltage Tester and set.
Set name
set value
Withstanding Voltage Tester
Test voltage
4,240 VPEAK
3,000 VRMS
3,000 VRMS
Set time
6 secs
Set current(Cutoff current)
4 mA
Unit
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzor sounds.
NG: The “NG” lamp lights and the buzzor sounds.
SHORT-CIRCUIT
AC POWER
SUPPLY CORD
AC POWER
SUPPLY CORD
CONNECT THE PROBE
TO GND TERMINAL
OF PHONO TERMINAL
TO GND TERMINAL
OF PHONO TERMINAL
PROBE
AC
UNIT
WITHSTANDING
VOLTAGE TESTER
VOLTAGE TESTER
+
-
OUT
OF CHASSIS
SCREW
IMPORTANT SERVICE NOTES (XL-505E FOR UK/XL-507E ONLY)
Specifications for this model are subject to change without
prior notice.
prior notice.
XL-505H/505E/507E
CP-505/505E/507
Click on the first or last page to see other XL-505E (serv.man5) service manuals if exist.