Read Sharp QT-CD50H (serv.man3) Service Manual online
QT-CD50
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
TO THE OPERATION MANUAL.
– 2 –
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are not
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassis
and other metal parts in the audio product.
and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,
cabinet, terminal board, adjustment and compartment
covers or shields, mechanical insulators etc.
covers or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage
current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15
µ
F capacitor in series with all exposed
metal cabinet parts and a known earth ground, such as
conduit or electrical ground connected to earth ground.
conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,
sensitivity to measure the AC voltage drop across the
resistor (See diagram).
resistor (See diagram).
* Connect the resistor connection to all exposed metal parts
having a return path to the chassis (antenna, metal cabinet,
screw heads, knobs and control shafts, escutcheon, etc.)
and measure the AC voltage drop across the resistor.
screw heads, knobs and control shafts, escutcheon, etc.)
and measure the AC voltage drop across the resistor.
IMPORTANT SERVICE NOTES
All check must be repeated with the AC line cord plug connection
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
AC.) or more is excessive and indicates a potential shock
hazard which must be corrected before returning the audio
product to the owner.
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
AC.) or more is excessive and indicates a potential shock
hazard which must be corrected before returning the audio
product to the owner.
SPECIFICATIONS
Tape recorder
Frequency response:
50 - 14,000 Hz (Normal tape)
Signal/noise ratio:
50 dB
Wow and flitter:
0.25 % (WRMS)
Motor:
DC 12 V electric governor
Bias system:
AC bias
Erase system:
Magnet Erase
Compact disc player
Type:
Compact disc
Signal readout:
Non-contact, 3-beam semi-
conductor laser pickup
conductor laser pickup
Audio channels:
2
Decoder:
16-bit linear quantization
Filter:
4-tims oversampling digital filter
D/A converter:
1-bit D/A converter
Wow and flutter:
Unmeasurable
(less than 0.001% W. peak)
(less than 0.001% W. peak)
General
Power source:
AC 120V, 60 Hz
DC 12 V [ "D" size (UM/SUM-1,
R20 or HP-2) battery x 8]
DC 12 V [ "D" size (UM/SUM-1,
R20 or HP-2) battery x 8]
Power consumption:
20 W
Output power:
FTC; 2.0 W minimum RMS per
channel into 8 ohms from 150 Hz to
20 kHz with no more than 10 % total
harmonic distortion.
RMS; 2.3 W (1.65 W + 1.65 W)
(DC operation, 10 % T.H.D)
channel into 8 ohms from 150 Hz to
20 kHz with no more than 10 % total
harmonic distortion.
RMS; 2.3 W (1.65 W + 1.65 W)
(DC operation, 10 % T.H.D)
Speakers:
4" (10 cm) full range speaker x 2
Output terminal:
Headphones; 16 - 50 ohms
(recommended; 32 ohms)
(recommended; 32 ohms)
Dimensions:
Width; 18-1/2" (470 mm)
Height; 6-1/2" (166 mm)
Depth; 8-7/8" (226 mm)
Height; 6-1/2" (166 mm)
Depth; 8-7/8" (226 mm)
Weight:
7.9 Ibs. (3.6 kg) without batteries
Radio
Frequency range:
FM; 87.6 - 108 MHz
AM; 530 - 1,720 kHz
AM; 530 - 1,720 kHz
Specifications for this model are subject to change without
prior notice.
prior notice.
AC SCALE
VTVM
1.5k ohms
10W
0.15
µ
F
TEST PROBE
TO EXPOSED
METAL PARTS
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
KNOWN EARTH
GROUND
Click on the first or last page to see other QT-CD50H (serv.man3) service manuals if exist.