Read Sharp QT-CD111H User Guide / Operation Manual online
please contact the dealer or supplier from whom it was
purchased. Where this is not possible, please contact
the telephone number listed below. You will then be
given details of how to obtain service.
Certain replacement parts and accessories may be ob-
tained from our main parts distributor.
during the guarantee period, you will need to provide
proof of the date of purchase to the repairing company.
Please keep your invoice or receipt, which is supplied at
the time of purchase.
able (moulded) plug incorporating a 3A fuse. Should the
fuse need to be replaced, a BSI or ASTA approved BS
1362 fuse marked or and of the same rating as
above, which is also indicated on the pin face of the plug
must be used.
use the plug without the fuse cover fitted.
not being compatible with the plug supplied, cut-off the
mains plug and fit an appropriate type.
the cut-off plug destroyed immediately and disposed of
in a safe manner.
serted elsewhere into a 13A socket outlet as a serious
electric shock may occur.
with the following code:
Blue : Neutral
Brown : Live
product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
the plug terminal which is marked N or coloured black.
to the plug terminal which is marked L or coloured red.
nected to the earth terminal in your three pin plug.
For the best performance, read this manual care-
fully. It will guide you in operating your SHARP
same as that removed from the cut-off plug.
lead and not simply over the lead wires.
letters in the parentheses indicate the colour of
the product. Operation and specifications are
position, mains voltage is still present inside the
This unit contains no user serviceable parts. Never
remove covers unless qualified to do so. This unit
contains dangerous voltages, always remove the
mains plug from the socket before any service oper-
ation and when not in use for a long period.
To prevent fire or shock hazard, do not expose this
appliance to dripping or splashing liquids.
procedures other than those specified herein
may result in hazardous radiation exposure.
player is harmful to the eyes, do not attempt to
disassemble the cabinet. Refer servicing to
qualified personnel only.
require consent, which SHARP is unable to give.
Please refer particularly to the provisions of the
Copyright Act 1956, the Dramatic and Musical
Performers Protection Act 1958, the Performers
Protection Acts 1963 and 1972 and to any sub-
sequent statutory enactments and orders.
of Directives 89/336/EEC and 73/23/EEC as
amended by 93/68/EEC.
than those in the drawing are not included.
or dust accumulate on the pickup, clean it gently
with a dry cotton swab.
poor sound and tape jams. Clean these parts
with a cotton swab moistened with commercial
head/pinch roller cleaner or isopropyl alcohol.
may become magnetised, causing poor sound.
Demagnetise these parts once every 30 hours of
playing/recording by using a commercial tape
head demagnetiser. Read the demagnetiser’s
instructions carefully before use.
a diluted soap solution, then wipe with a dry cloth.
insecticides on the unit.
tures higher than 60˚C (140˚F) or to extreme low
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home compu-
ters, facsimiles, etc.) which generates electrical
moving it from the AC socket, since pulling the
lead can damage internal wires.
remove the AC power plug from the wall socket
as the unit contains high voltages.
Do not remove the outer cover, as this may result
in electric shock. Refer internal service to your
local SHARP service facility.
vibration, and do not place anything on the top
of the unit.
set the FUNCTION switch to STAND-BY and
then to ON again.
is suggested that you disconnect the AC power
lead from the AC socket for safety.
The voltage used must be the same as that specified
on this unit. Using this product with a higher voltage
other than which is specified is dangerous and may
result in a fire or other type of accident causing
damage. SHARP will not be held responsible for any
damage resulting from use of this unit with a voltage
other than that which is specified.
in an extremely humid environment may cause con-
densation inside the cabinet (CD pickup, tape
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc (or
cassette) in the unit until normal playback is possible
(about 1 hour).
time, remove the AC power lead from the AC
disconnects the batteries.
supplied. Use of a power lead other than the one
supplied may cause an electric shock or fire.
indicated on the rear panel.
unit will not be used for long periods of time. This
will prevent potential damage due to battery
Do not use rechargeable batteries (nickel-cadmium
Replace the batteries when they become weak
and/or recording or playback is impaired. This may
occur even though radio broadcasts are audible.
ever mistracking can occur due to an accumulation
of dirt on the disc surface.
from your CD collection and player.
the non-label side. Signals are read from the
non-label side. Do not mark this surface.
and excessive moisture.
dirt, or water on the CDs can cause noise or
mistracking. If a CD is dirty or does not play
properly, clean it with a soft, dry cloth, wiping
straight out from the centre, along the radius.
the best sound. (Metal or CrO
For recording, use only normal tape.
diameter reels, or poor-quality tapes, as they
may cause malfunctions.
ment, tighten the slack with a pen or pencil.
accidental recording or erasing from taking
place. Removing the tab will protect the corre-
sponding side from being erased. Cover the tab
holes with adhesive tape to erase or record
R20, HP-2 or similar)
STAND-BY • ON
phones have a 3.5 mm
(1/8") diameter plug
and are between 16
ohms and 50 ohms im-
pedance. The recom-
mended impedance is