Read Sharp HT-CN500DVH User Guide / Operation Manual online
E-50
HTCN400_500DVH_E.fm
03/7/2
HT-CN400DVH
ENGLISH
92LCN400E0270
F
S
V
I
N
P
E
D
HT-CN500DVH
Re
fe
re
nc
es
- T
roub
le
s
h
ooting c
h
a
rt -
!
Tuner
!
Remote control
!
If trouble occurs
When this product is subjected to strong external interference (mechanical shock,
excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is
operated incorrectly, it may malfunction.
excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is
operated incorrectly, it may malfunction.
When the protection circuit is activated:
When short-circuiting the speaker leads or turning the volume too high, the protection
circuit may be activated and the system may enter the stand-by mode.
Unplug the unit and, after 15 minutes or more, plug it in again.
Turn down the volume if set too high.
circuit may be activated and the system may enter the stand-by mode.
Unplug the unit and, after 15 minutes or more, plug it in again.
Turn down the volume if set too high.
!
Before transporting the unit
!
Condensation
Sudden temperature changes, storage or operation in an extremely humid environ-
ment may cause condensation inside the cabinet (laser pickup, etc.) or on the trans-
mitter on the remote control.
Condensation can cause the unit to malfunction. If this happens, leave the power on
with no disc in the unit until normal playback is possible (about 1 hour). Wipe off any
condensation on the transmitter with a soft cloth before operating the unit.
ment may cause condensation inside the cabinet (laser pickup, etc.) or on the trans-
mitter on the remote control.
Condensation can cause the unit to malfunction. If this happens, leave the power on
with no disc in the unit until normal playback is possible (about 1 hour). Wipe off any
condensation on the transmitter with a soft cloth before operating the unit.
Symptom
Possible cause
Reference
page
The radio makes unusual
noises continuously.
noises continuously.
"
Is the unit placed near the TV or
computer?
computer?
"
Is the FM aerial or AM loop aerial
placed properly? Move the aerial
away from the AC power lead or the
unit if located near.
placed properly? Move the aerial
away from the AC power lead or the
unit if located near.
P. 12
The preset channel cannot
be recalled.
be recalled.
"
Did you remove the plug from the
wall socket, or did a power failure
occur?
wall socket, or did a power failure
occur?
P. 40
Set the channel again.
Symptom
Possible cause
Reference
page
The remote control does not
operate properly.
operate properly.
"
Is the battery polarity respected?
P. 16
"
Are the batteries dead?
"
Is the distance or angle incorrect?
P. 16
"
Are there any obstructions in front of
the unit?
the unit?
"
Is the remote control sensor ex-
posed to strong light (inverter fluo-
rescent light, direct sunlight, etc.)?
posed to strong light (inverter fluo-
rescent light, direct sunlight, etc.)?
P. 16
"
Is the remote control for another
equipment used simultaneously?
equipment used simultaneously?
The unit cannot be turned on
with the remote control.
with the remote control.
"
Is the AC power lead of the unit
plugged in?
plugged in?
P. 14
"
Are the batteries inserted?
P. 16
If such a problem occurs, do the following:
1
Set the unit to the stand-by mode and turn the power on again.
2
If the unit is not restored in the previous operation, unplug and plug in the unit, and
then turn the power on.
then turn the power on.
1 Press the ON/STAND-BY button to turn the power on.
2 Press the OPEN/CLOSE button to open the disc tray.
2 Press the OPEN/CLOSE button to open the disc tray.
Remove the disc inserted in the unit.
3 Press the OPEN/CLOSE button to close the disc tray.
4 Press the ON/STAND-BY button to enter the stand-by mode, and
4 Press the ON/STAND-BY button to enter the stand-by mode, and
then unplug the AC power lead from the wall socket.
Click on the first or last page to see other HT-CN500DVH service manuals if exist.