GX-M10H (serv.man2) - Sharp Audio User Guide / Operation Manual. Page 21

Reusing the memorised timer setting:
The timer setting will be memorised once it is entered. To reuse 
the same setting, perform the following operations.

1  Turn the power on and press and hold down the CLOCK/TIMER 

button.

2  Within 10 seconds, press the 

 or 

 button to select 

“ONCE” or “DAILY”, and press the ENTER button.

3  Within 10 seconds, press the 

 or 

 button to select 

“TIM.ON” , and press the ENTER button.

4  Press the ON/STAND-BY button to enter the power stand-by 

mode.

The radio, compact disc, iPod, USB, and Audio In function can all 
be turned off automatically.

1  Play back the desired sound source.
2  Press the SLEEP button.
3  Within 5 seconds, press the Numeric button to set the time. (1 

minute ~ 99 minutes)

4  “SLEEP” will appear.
5  The unit will enter the power stand-by mode automatically after 

the preset time has elapsed. The volume will be turned down 1 
minute before the sleep operation fi nishes

To confi rm the remaining sleep time:
1  Whilst “SLEEP” is indicated, press the SLEEP button.

To cancel the sleep operation:
Press the ON/STAND-BY button whilst “SLEEP” is indicated.  To 
cancel the sleep operation without setting the unit to the stand-by 
mode, proceed as follows.

1  Whilst “SLEEP” is indicated, press the SLEEP button.
2  Within 5 seconds, press the “0” button twice until “SLEEP 00” 

appears.

Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up 
to CD in the next morning.
1  Set the sleep time (see above, steps 1 - 5).
2  Whilst the sleep timer is set, set the timer playback (steps 2 - 9, 

page 19).

Sleep timer 
setting

Timer playback 
setting

End time

1-99 minutes

Desired time

Sleep operation will 

automatically stop

Timer playback start time

Many potential problems can be resolved by the owner without 
calling a service technician.

If something is wrong with this product, check the following before 
calling your authorised SHARP dealer or service centre.

  The clock is not set to 

the correct time.

  A power failure occured.
  Reset the clock. (Refer page 6)

  When a button is 

pressed, the unit does 
not respond.

  Set the unit to the power 

stand-by mode and then turn 
it back on.

  If the unit still malfunctions, 

reset it. (Refer page 21)

  No sound is heard.

  The volume level is set to 

“MIN”.

  The headphones are 

connected.

  Sound too low or 

distorted.

  Power suddenly shuts 

down.

  The batteries are depleted. 

Change the batteries.

  Playback does not start.
  Playback stops in 

the middle or is not 
performed properly.

  The disc is loaded upside 

down.

  The disc does not satisfy the 

standards.

  The disc is  distorted or 

scratched.

  Playback sounds are 

skipped, or stopped in 
the middle of a track.

  The unit is located near 

excessive vibrations.

  A very dirty disc has been used.
  Condensation has formed 

inside the unit.

  Volume level is too high. Adjust 

to lower volume.

  The remote control does 

not operate.

  The AC power lead of the unit is 

not plugged in.

  Wrong battery polarity.
  The batteries are exhausted.
  The distance or angle is 

incorrect.

  The remote control sensor 

receives strong light or sunlight.

  The radio makes 

unusual noises 
continuously.

  The unit is placed near the TV 

or computer.

  The FM aerial is not properly 

extended or positioned.

GX-M10H_OM_UK_OK_JU.indd   Sek1:20

GX-M10H_OM_UK_OK_JU.indd   Sek1:20

2012-08-14   23:23:56

2012-08-14   23:23:56