Read Sharp DK-V2 User Guide / Operation Manual online
8
DK-V2
Preparation for Use
Power source (continued)
Using with the batteries
Battery replacement:
When batteries are low, sound decreases or becomes distorted.
Reduce the volume level or replace the batteries with new ones.
When batteries are low, sound decreases or becomes distorted.
Reduce the volume level or replace the batteries with new ones.
Battery life
Note:
Battery life may vary depending on the temperature, battery types
and usage conditions.
Precautions for battery use:
Battery life may vary depending on the temperature, battery types
and usage conditions.
Precautions for battery use:
Installing the batteries incorrectly may cause the unit to malfunction.
Insert the batteries according to the direction indicated in the battery
compartment.
Insert the batteries according to the direction indicated in the battery
compartment.
Remove the batteries if the unit is not to be used for long periods
of time. This will prevent potential damage due to battery leakage.
When using batteries, the brightness of all illumination light
(indicators) is reduced compared to using AC/DC adaptor.
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
of time. This will prevent potential damage due to battery leakage.
When using batteries, the brightness of all illumination light
(indicators) is reduced compared to using AC/DC adaptor.
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Batteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
Caution:
Do not use rechargeable batteries (nickeI-cadmium battery,etc.).
Changing power source:
Turn off the unit before changing the power source.
Do not use rechargeable batteries (nickeI-cadmium battery,etc.).
Changing power source:
Turn off the unit before changing the power source.
General control
To turn the power on
Press the ON/STAND-BY button to turn the power on. The
illuminator around the ON/STAND-BY button turns blue.
illuminator around the ON/STAND-BY button turns blue.
Volume control
Press the VOL + or – button to increase or decrease the volume.
Note:
Pairing light indicator will blink when volume reaches minimum or
maximum.
Note:
Pairing light indicator will blink when volume reaches minimum or
maximum.
Bass control (X-BASS)
When the X-BASS button is pressed, the unit will enter the extra bass
mode and the X-BASS indicator turns yellowish orange. To cancel
this mode, press the X-BASS button again.
mode and the X-BASS indicator turns yellowish orange. To cancel
this mode, press the X-BASS button again.
1
Disconnect the AC/DC adaptor, and open the battery
compartment.
compartment.
2
Insert 4 “AA” size batteries (UM-3, R6 or similar) into the
battery compartment.
“AA” size batteries (UM-3, R6 or similar) are not included.
Battery Insertion:
Slide in batteries 1
Battery Insertion:
Slide in batteries 1
1
1
1 and 3
3
3
3. Then push batteries 2
2
2
2 and 4
4
4
4
towards .
Battery removal:
Push batteries 2
Battery removal:
Push batteries 2
2
2
2 and 4
4
4
4 towards and remove the batteries
before sliding out batteries 1
1
1
1 and 3
3
3
3.
3
Close the battery compartment.
4
Pairing indicator and illuminator around the ON/STAND-BY
button will blink blue light once before disappearing and
the STAND-BY indicator turns red. Remove the batteries if
the unit is not to be used for long periods of time to prevent
battery leakage which may cause potential damage.
the STAND-BY indicator turns red. Remove the batteries if
the unit is not to be used for long periods of time to prevent
battery leakage which may cause potential damage.
Battery type
ALKALINE (AA) (1.5V)
Usage time
Approx. 4 hrs.
Output
74mW + 74mW
2
+
+
+
3
4
+
1
After use:
Press the ON/STAND-BY button to turn off the unit.
It takes a few seconds for the blue illuminator around the
ON/STAND-BY button to go off.
Press the ON/STAND-BY button to turn off the unit.
It takes a few seconds for the blue illuminator around the
ON/STAND-BY button to go off.
Click on the first or last page to see other DK-V2 service manuals if exist.