Read Sharp DK-KP85H (serv.man2) Service Manual online
DK-KP85PH
– 1
The Bluetooth
®
word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by SHARP is under license.
Other trademarks and trade names are those of their respective owners.
Other trademarks and trade names are those of their respective owners.
iPad, iPhone, iPod, iPod classic, iPod nano, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries. Lightning is a trademark of Apple Inc.
trademarks of Apple Inc., registered in the U.S. and other
countries. Lightning is a trademark of Apple Inc.
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean
that an electronic accessory has been designed to connect
specifically to iPod, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note
that the use of this accessory with iPod, iPhone, or iPad may
affect wireless performance.
that an electronic accessory has been designed to connect
specifically to iPod, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note
that the use of this accessory with iPod, iPhone, or iPad may
affect wireless performance.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
after sales service only.
The contents are subject to change without notice.
PRECAUTIONS FOR USING LEAD-FREE SOLDER
CHAPTER 1. GENERAL DESCRIPTION
[1] Important Service Notes (for U.K. only)....... 1-1
[2] AC
[1] Important Service Notes (for U.K. only)....... 1-1
[2] AC
Power
Supply Cord................................ 1-1
[3] Specifications .............................................. 1-2
[4] Name Of Parts............................................. 1-3
[4] Name Of Parts............................................. 1-3
CHAPTER 2. ADJUSTMENTS
[1] CD
[1] CD
Section .................................................. 2-1
[2] Version Check ............................................. 2-1
CHAPTER 3. MECHANICAL DESCRIPTION
[1] Disassembly ................................................ 3-1
[1] Disassembly ................................................ 3-1
CHAPTER 4. FLOWCHART
[1] Troubleshooting ........................................... 4-1
[1] Troubleshooting ........................................... 4-1
CHAPTER 5. MAJOR PART DRAWING
[1] Function Table Of IC.................................... 5-1
[2] FL
[1] Function Table Of IC.................................... 5-1
[2] FL
Display.................................................. 5-14
CHAPTER 6. CIRCUIT DESCRIPTION
[1] Waveforms Of CD Circuit ............................ 6-1
[2] IC
[1] Waveforms Of CD Circuit ............................ 6-1
[2] IC
Voltage .................................................... 6-2
CHAPTER 7. DIAGRAM
[1] Main/Amplifier Block Diagram ..................... 7-1
[2] Voltage And Current Block Diagram ............ 7-2
[1] Main/Amplifier Block Diagram ..................... 7-1
[2] Voltage And Current Block Diagram ............ 7-2
CHAPTER 8. CIRCUIT SCHEMATICS AND PARTS
LAYOUT
[1] Notes On Schematic Diagram ..................... 8-1
[2] Type
LAYOUT
[1] Notes On Schematic Diagram ..................... 8-1
[2] Type
Of
Transistor And LED ........................ 8-1
[3] Schematic Diagram ..................................... 8-2
[4] Chart Of Connecting Wires ......................... 8-8
[5] Wiring
[4] Chart Of Connecting Wires ......................... 8-8
[5] Wiring
Side Of PWB .................................... 8-9
PARTS GUIDE
SERVICE MANUAL
No. S5309DKKP85PH
CONTENTS
SLIM MICRO SYSTEM
MODEL
DK-KP85PH
SHARP CORPORATION
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
!
• In the interests of user-safety (Required by safety regulations in
some countries) the set should be restored to its original condition
and only parts identical to those specified be used.
and only parts identical to those specified be used.
DK-KP85PH
– 2
1. Employing lead-free solder
Example:
Indicates lead-free solder of tin, silver and copper.
2. Using lead-free wire solder
3. Soldering
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with
conventional lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we
recommend you to use a dedicated soldring bit, if you are not familiar with how to obtain lead-free wire solder
or soldering bit, contact our service station or service branch in your area.
conventional lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we
recommend you to use a dedicated soldring bit, if you are not familiar with how to obtain lead-free wire solder
or soldering bit, contact our service station or service branch in your area.
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead
solder by 40 C, and as it has poor solder wet ability, you may be apt to keep the soldering bit in contact with the
PWB for extended period of time. However, since the land may be peeled off or the maximum heat-resistance
temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady
soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corrected. Make sure to turn on
and off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit
after every use of it.
solder by 40 C, and as it has poor solder wet ability, you may be apt to keep the soldering bit in contact with the
PWB for extended period of time. However, since the land may be peeled off or the maximum heat-resistance
temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady
soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corrected. Make sure to turn on
and off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit
after every use of it.
"MAIN, DISPLAY, TRANSIT, SMPS, LED, KEY, TUNER, TUNER PACK, REMOTE SENSOR, SWITCH PWB" of this
model employs lead-free solder.
The LF symbol indicates lead-free solder, and is attached on the PWB and service manuals. The alphabetical
character following LF shows the type of lead-free solder.
model employs lead-free solder.
The LF symbol indicates lead-free solder, and is attached on the PWB and service manuals. The alphabetical
character following LF shows the type of lead-free solder.
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Ref No.
Description
Parts No.
PWB-A 92LPWB8871
MANS
MAIN (A1) / DISPLAY (A2) / TRANSIT (A3)
PWB-B RUiTZA087AWZZ SMPS
PWB-C 92LPWB8870
TUNS
LED (C1) / KEY (C2) / TUNER (C3) / TUNER PACK (C4) / REMOTE SENSOR (C5) / SWITCH (C6)
i
DK-KP85PH
1 – 3
CHAPTER 1. GENERAL DESCRIPTION
[2]
AC Power Supply Cord
CAUTION : “Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type”.
equivalent type”.
[1] Important Service Notes (for U.K. only)
Before returning the unit to the customer after completion of a repair or adjustment it is necessary for the following withstand voltage test to
be applied to ensure the unit is safe for the customer to use.
be applied to ensure the unit is safe for the customer to use.
Setting of Withstanding Voltage Tester and set.
Set name
set value
Withstanding Voltage Tester
Test voltage
Test voltage
4,240 VPEAK
3,000 VRMS
3,000 VRMS
Set time
6 secs
Set current (Cutoff current)
4 mA
Unit
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzer sounds.
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzer sounds.
PROBE
AC
OUT
AC/DC
ADAPTOR
SHORT-CIRCUIT
AC POWER
SUPPLY CORD
AC POWER
SUPPLY CORD
CONNECT THE PROBE
TO SHELL OF DC CONNECTOR
WITHSTANDING
VOLTAGE TESTER
QACCE0016AW00
QACCBA008AW00
1 – 1
DK-KP85PH
1 – 4
[3] Specifications
General
Amplifier
Tuner
USB (MP3 / WMA)
CD player
Frequency range FM: 87.5 - 108 MHz
AM: 522 - 1,620 kHz
Preset
40 (FM and AM station)
Power source
AC 220 - 240 V ~ 50/60 Hz
Power
consumption
consumption
Power on: 24 W
Power stand-by: 0.4 W (*)
Power stand-by: 0.4 W (*)
Speaker
1-way speaker system
Speaker: 10 cm (4”) - 6 ohms - Full
Range
Speaker: 10 cm (4”) - 6 ohms - Full
Range
Speaker
maximum input
power
maximum input
power
50 W/channel
Speaker rated
input power
input power
25 W/channel
Frequency band
2.400GHz - 2.480GHz
Compatible
Bluetooth
Bluetooth
A2DP (Advanced Audio Distribution
Bluetooth
2.1 +EDR
Dimensions
Width: 475 mm (18 - 11/16”)
Height: 191 mm (7 - 1/2”)
Depth: 83 mm (3 - 1/4”)
Height: 191 mm (7 - 1/2”)
Depth: 83 mm (3 - 1/4”)
Weight
2.45 kg (5.4 lbs.)
Output power
Output terminals
Headphones: 16 ohms
(recommended: 32 ohms)
(recommended: 32 ohms)
Input terminals
Audio In (audio signal):
500 mV/47 k ohms
500 mV/47 k ohms
Type
Single disc multi-play compact disc
player
player
Signal readout
Non-contact, 3-beam
semiconductor laser pickup
semiconductor laser pickup
D/A converter
Multi bit D/A converter
Frequency
response
response
20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
USB host
interface
interface
Complies with USB 1.1 (Full
Speed)/2.0 Mass Storage Class.
Support Bulk only and CBI
protocol.
Speed)/2.0 Mass Storage Class.
Support Bulk only and CBI
protocol.
MPEG 1 Layer 3
WMA (Non DRM)
WMA (Non DRM)
Bitrate support
Support file
MP3 (32 ~ 320 kbps)
WMA (64 ~ 160 kbps)
WMA (64 ~ 160 kbps)
Other
Maximum total number of MP3/
Maximum total number of folders is
999 INCLUSIVE of root directory.
The ID3TAG information supported
are TITLE, ARTIST and ALBUM only.
Supports ID3TAG version 1 and
version 2.
999 INCLUSIVE of root directory.
The ID3TAG information supported
are TITLE, ARTIST and ALBUM only.
Supports ID3TAG version 1 and
version 2.
File system
support
support
Support USB devices with
Microsoft Windows/DOS/FAT
12/FAT 16/ FAT 32.
2 kbyte block length for sector.
Microsoft Windows/DOS/FAT
12/FAT 16/ FAT 32.
2 kbyte block length for sector.
Profile
Profile), AVRCP (Audio/Video
Remote Control Profile)
WMA files is 65025.
PMPO: 100
WMPO: 50 W (25 W + 25 W)
(10% T.H.D.)
RMS: 50 W (25 W + 25 W)
(10% T.H.D.)
RMS: 40 W (20 W + 20 W)
(1% T.H.D.)
WMPO: 50 W (25 W + 25 W)
(10% T.H.D.)
RMS: 50 W (25 W + 25 W)
(10% T.H.D.)
RMS: 40 W (20 W + 20 W)
(1% T.H.D.)
( * ) This power consumption value is obtained when the
demonstration mode is cancelled in the power stand-by
mode.
demonstration mode is cancelled in the power stand-by
mode.
1 – 2
