CP-SW1000H (serv.man2) - Sharp Audio Service Manual (repair manual)

cp-sw1000h (serv.man2) service manual
Model
CP-SW1000H (serv.man2)
Pages
62
Size
8.13 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio / System
File
cp-sw1000h-sm2.pdf
Date

Read Sharp CP-SW1000H (serv.man2) Service Manual online

CP-SW1000H
 – 1
SUBWOOFER SYSTEM
  SERVICE MANUAL
No. S9748CPW100HH
• In the interests of user-safety the set should be restored to
its original condition and only parts identical to those
specified be used.
PRECAUTIONS FOR USING LEAD-FREE SOLDER
CHAPTER 1. GENERAL DESCRIPTION
[1]  Important Service Notes (for U.K. only) ........... 1-1
[2] Specifications .................................................. 1-1
[3]  Name Of Parts................................................. 1-2
CHAPTER 2. MECHANICAL DESCRIPTION
[1] Disassembly .................................................... 2-1
CHAPTER 3. DIAGRAMS
[1] Block Diagram ................................................. 3-1
CHAPTER 4. CIRCUIT DESCRIPTION
[1] Voltage ............................................................ 4-1
[2]  Waveforms Of SUBWOOFER Circuit.............. 4-2
CHAPTER 5. CIRCUIT SCHEMATICS AND PARTS
LAYOUT
[1]  Notes On Schematic Diagram ......................... 5-1
[2]  Types Of Transistor And LED.......................... 5-1
[3]  Chart Of Connecting Wires.............................. 5-2
[4] Schematic Diagram ......................................... 5-4
[5]  Wiring Side Of PWB ...................................... 5-14
CHAPTER 6. OTHERS
[1]  Function Table Of IC........................................ 6-1
PARTS GUIDE
Parts marked with "      " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
CONTENTS
CP-SW1000H
MODEL
SHARP CORPORATION
(For Europe, U.K.)
• Note for users in U.K.
Recording and playback of any material may require
consent which SHARP is unable to give. Please refer
particularly to the provisions of Copyright Act 1956, the
Performers Protection Acts 1963 and 1972 and subsequent
statutory enactments and orders.
CP-SW1000H
 – 2
 
PRECAUTIONS FOR USING LEAD-FREE SOLDER
1. Employing lead-free solder
Example:
Indicates lead-free solder of tin, silver and copper.
Lead-free wire solder for servicing
Ref No.
Description
Parts No.
PWB-A
92LPWB6944PWRS
POWER (A1), MAIN (A2), CROSS OVER (A3), VOLUME (A4), LED (A5)
PWB-B
92LPWB6944SWFS
SUBWOOFER
"POWER, MAIN, CROSS OVER, VOLUME, LED, SUBWOOFER PWB" of this model employs lead-free solder. 
The LF symbol indicates lead-free solder, and is attached on the PWB and service manuals. The alphabetical 
character following LF shows the type  of lead-free solder.
2. Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional 
lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend 
you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering 
bit, contact our service station or service branch in your area.
3. Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead 
solder by 40°C,and as it has poor solder wet ability, you may be apt to keep the soldering bit in contact with the 
PWB for extended period of time. However, since the land may be peeled of for the maximum heat-resistance 
temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady 
soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corrected. Make sure to turn 
on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is 
alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sand paper.
Be careful when replacing parts with polarity indication on the PWB silk.
i
CP-SW1000H
1 – 3
CHAPTER 1. GENERAL DESCRIPTION
[2] Specifications
[1] Important Service Notes (for U.K. only)
Before returning the unit to the customer after completion of a repair or adjustment it is necessary for the following withstand voltage test to be
applied to ensure the unit is safe for the customer to use.
Setting of Withstanding Voltage Tester and set.
Set name
set value
Withstanding Voltage Tester
Test voltage
4,240 VPEAK
3,000 VRMS
Set time
6 secs
Set current (Cutoff current)
4 mA
Unit
Judgment
OK: The “GOOD” lamp lights.
NG: The “NG” lamp lights and the buzzer sounds.
PROBE
AC
OUT
AC/DC
ADAPTOR
SHORT-CIRCUIT
AC POWER
SUPPLY CORD
CONNECT THE PROBE
TO SHELL OF DC CONNECTOR
WITHSTANDING
VOLTAGE TESTER
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.
 
CP-SW1000H
CP-SW1000H for U.K.
General
Power source
AC 220 - 240 V ~ 50 Hz
Power consumption
Power on: 18 W
Power stand-by: 0.6 W(*)
Amplification system
Subwoofer: Pulse width modulation
Output power
RMS: 100 W (50 W + 50 W) (DIN 45 324)
Audio input terminal
Analog input: RCA type x 1 pair (L/R)
Type
Subwoofer system
Impedance
4 ohms x 2
Dimensions
Width: 430 mm (16-15/16") 
Height: 151 mm (5-15/16") 
Depth: 323.5 mm (12-3/4")
Weight
6.4 kg (14.11 lbs.)
Crossover frequency
80 Hz - 220 Hz
( * ) This power consumption value is obtained when in the power 
stand-by mode.
CAUTION: “Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type”.
General
Power source
AC 220 - 240V ~ 50 Hz
Power consumption
Power on: 18 W
Power stand-by: 0.6 W(*)
Amplification system
Subwoofer: Pulse width modulation
Output power
RMS: 100 W (50 W + 50 W) (10% T.H.D.)
Audio input terminal
Analog input: RCA type x 1 pair (L/R)
Type
Subwoofer system
Impedance
4 ohms x 2
Dimensions
Width: 430 mm (16-15/16") 
Height: 151 mm (5-15/16") 
Depth: 323.5 mm (12-3/4")
Weight
6.4 kg (14.11 lbs.)
Crossover frequency
80 Hz - 220 Hz
( * ) This power consumption value is obtained when in the power stand-
by mode.
1 – 1
CP-SW1000H
1 – 4
[3] Names Of Parts
5 6
4
3
2
1
1 2 3
2
4
3
1
Front panel
1. Bass Reflex Duct
2. Remote Sensor
3. Volume Control
4. Crossover Frequency Control
5. ON/STAND-BY Button
6. STAND-BY Indicator
Rear panel
1. AC Input
2. Cooling Fan
3. Audio Input
Remote control
1. Remote Control Transmitter
2. On/Stand-by Button
3. TV Operation Buttons
4. Volume Up and Down Buttons
1 – 2
Page of 62
Display

Download Sharp CP-SW1000H (serv.man2) Service Manual (Repair Manual)

Here you can read online and download Sharp CP-SW1000H (serv.man2) Service Manual in PDF. CP-SW1000H (serv.man2) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp CP-SW1000H (serv.man2) System. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.